What to do if Black & Decker BXPW1700PE pump pressure drops suddenly during use?
If the Black & Decker Pressure Washer pump pressure suddenly drops during use, it might be because the water is being sucked from an external tank. Try connecting the appliance to the mains water supply. Also, the inlet water could be too hot, so reduce the temperature. Check if the nozzle or inlet filter is clogged and clean them.
How to fix Black & Decker Pressure Washer not sucking detergent?
If there's no detergent being sucked into your Black & Decker Pressure Washer, ensure the adjustable nozzle isn't on a high-pressure setting; set it to the " " setting. The detergent might be too dense, so try diluting it with water. If you're using a high-pressure hose extension, fit the original hose.
Why Black & Decker BXPW1700PE Pressure Washer motor buzzes but fails to start?
If your Black & Decker Pressure Washer motor buzzes but won't start, the power supply voltage may be too low. Check that the mains power supply line voltage matches what's on the appliance's plate. Also, voltage drop could occur due to the use of an extension cable; examine the characteristics of the extension cable.
Why Black & Decker BXPW1700PE motor fails to start?
If your Black & Decker Pressure Washer motor fails to start, first, check that the plug is firmly in the socket and that the mains voltage supply is present. If the appliance hasn't been used for a while, use the tool to unjam the motor through the hole at the rear of the appliance (in models with this feature).
Why water escapes from thermo- stat valve of Black & Decker BXPW1700PE Pressure Washer?
If water escapes from the thermo-stat valve of your Black & Decker Pressure Washer, it means the water temperature inside the pump head has exceeded the maximum rated value stated on the nameplate. When the appliance is in operation, avoid stopping the water jet for more than 5 minutes at a time.
Why is my Black & Decker BXPW1700PE so noisy?
If your Black & Decker Pressure Washer is excessively noisy, the water may be too hot. Try reducing the water temperature.
What to do if my Black & Decker BXPW1700PE Pressure Washer has no water delivery when gun trigger is depressed?
If there's no water delivery when the gun trigger is depressed on your Black & Decker Pressure Washer (with the supply hose connected), the nozzle might be clogged. Try cleaning the nozzle.
Why is my Black & Decker Pressure Washer pump not reaching working pressure?
If the Black & Decker Pressure Washer pump isn't reaching working pressure, several factors could be at play. A worn nozzle can be the culprit, so consider replacing it. The water filter might be clogged; try cleaning it. Ensure the water supply tap is fully open to provide sufficient water. Air could be getting sucked into the system, so check the tightness of hose fittings. If there's air in the pump, switch off the appliance, repeatedly depress and release the gun trigger until the water flows steadily, then switch it back on. Also, make sure the adjustable nozzle is correctly positioned on the (+) setting. In some cases, the thermostatic valve may have tripped, requiring you to wait for the correct water temperature to restore. Finally, ensure that water isn't being sucked from an open...
Details hazard, E2 (professional use), E3 (non-professional use), and moving parts symbols.
Lists essential PPE for safe operation, including ear defenders, gloves, and clothing.
Critical warnings against misuse, improper pointing, and tampering with safety devices.
Essential precautions for electrical safety, water supply connection, and operator protection.
Details on controls, starting, stopping, and restarting the appliance.
Addresses problems like low pressure, motor issues, leaks, and no detergent suction.
General| AC input voltage | 220 - 240 V |
|---|---|
| Power consumption (typical) | 1700 W |
| Maximum flow rate | 420 l/h |
| Use with foam nozzle | Yes |
| Working pressure (max) | 130 bar |
| Form factor | Upright |
| Hose length | 6 m |
| Power source | Electric |
| Product color | Black, Orange |
| Pressure range | High-pressure |
| Quantity per pack | 1 pc(s) |
Weight and Dimensions| Weight | 10600 g |
|---|
To Next Page