How to fix a garden hose connection leak on my Black & Decker BEPW1750?
If the garden hose connection on your Black & Decker Pressure Washer leaks, tighten the fittings. If the rubber washer is missing or worn, replace it in the hose adapter.
Why Black & Decker BEPW1750 Pressure Washer motor does not start?
The motor may not start due to several reasons: the unit isn't plugged in (plug in the power cord); the ON/OFF switch is in the OFF position (turn the switch to the “ON” position); or the wand trigger isn't being squeezed (squeeze the trigger with the switch in the “ON” position).
What to do if Black & Decker BEPW1750 Pressure Washer motor buzzes but fails to run?
If the motor buzzes but doesn't run, it could be due to supply voltage being below the minimum (verify that only the pressure washer is running on the circuit), the system having residual pressure (turn the unit off, squeeze the trigger on the spray wand to release pressure, then turn the unit on), or voltage loss due to an extension cord (plug directly into the outlet).
How to fix garden hose connection leaks on Black & Decker BEPW1750?
Garden hose connection leaks are often due to loose fittings (tighten the fittings) or a missing/worn rubber washer (replace the washer in the hose adapter).
Why is my Black & Decker Pressure Washer not reaching high pressure?
If your Black & Decker Pressure Washer isn't reaching high pressure, fully open the water valve and check the water hose for any kinks, leaks, or blockages that may be restricting the water supply. Clean the water inlet filter by removing it and rinsing it. If the nozzle is worn, replace it with a new one. Ensure hoses and fittings are airtight, and purge the pump by turning off the machine and squeezing the trigger gun until water flows steadily from the nozzle. If the unit is not properly self-primed, refer to Self Priming under Assembly.
Why does my Black & Decker Pressure Washer pressure go up and down?
If the output pressure of your Black & Decker Pressure Washer varies, ensure you have enough inlet water supply by turning the water on full force and checking the hose for leaks and kinks. Also, check that the hoses and fittings are airtight, and purge the pump by turning the machine off and squeezing the trigger gun until a steady flow of water emerges from the nozzle. Clean the water inlet screen by rinsing it off with water, and clear any obstructions from the discharge nozzle.
What to do if my Black & Decker BEPW1750 Pressure Washer motor buzzes but doesn't run?
If your Black & Decker Pressure Washer motor buzzes but fails to run, ensure that only the pressure washer is running on the circuit to verify the supply voltage is above the minimum. Turn the unit off, squeeze the trigger on the spray wand to release any residual pressure, and then turn the unit back on. Plug the unit directly into the outlet to avoid voltage loss from an extension cord. If the cleaner has not been used for a long period, contact your local dealer.
Why is my Black & Decker BEPW1750 not dispensing detergent?
If there is no detergent coming out of your Black & Decker Pressure Washer, first, ensure the detergent container is filled with detergent recommended for pressure washers only. Check that the detergent bottle or suction tube is properly connected. Clean the filter on the detergent suction tube by running warm water through it to remove any debris. If the detergent suction tube is damaged or clogged, remove the obstruction or replace the tube. Also, blow out or remove any debris from the discharge nozzle.
Why is the pump on my Black & Decker BEPW1750 Pressure Washer so noisy?
If your Black & Decker Pressure Washer pump is excessively noisy, check that all hoses and fittings are airtight. Turn the machine off and purge the pump by squeezing the trigger gun until a steady flow of water emerges from the nozzle.
Why is my Black & Decker Pressure Washer spray wand leaking?
If the spray wand on your Black & Decker Pressure Washer leaks, make sure the spray wand is properly attached by inserting it into the spray handle and pushing it in and turning it to lock it into place. If the O-ring is broken, contact your local dealer.
General| Power Source | Electric |
|---|---|
| Maximum Pressure | 1750 PSI |
| Water Flow Rate | 1.2 GPM |
| Flow Rate | 1.2 GPM |
| Weight | 17.2 lbs |
| Hose Length | 20 ft |
| Cord Length | 35 ft |
Essential precautions for safe operation, including cord handling, operator awareness, and area clearance.
Guidelines on electrical connections, cord condition, and avoiding electric shock hazards.
Rules for safe operation, including nozzle use, hand positioning, and chemical handling.
Advice on chemical use, environmental conditions, and potential hazards like gas vapors.
Warnings regarding accidental discharge, hose leaks, and use of non-approved accessories.
Precautions for machine integrity, use of original parts, and handling of water flow.
Instructions for protecting others and understanding tool safety symbols.
Solutions for problems like the motor not starting or low pressure output.
Troubleshooting tips for leaks in fittings, spray wand, and noisy pump operation.
Diagnosing and resolving problems when no detergent is dispensed.
To Next Page
