Black & Decker BEPW1750

Other manuals for Black & Decker BEPW1750

Manual48 pages

Instruction Manual36 pages

Questions and Answers

M
maria25Sep 2, 2025
Why is my Black & Decker BEPW1750 not dispensing detergent?
- L
  Lisa EdwardsSep 2, 2025
  If there is no detergent coming out of your Black & Decker Pressure Washer, first, ensure the detergent container is filled with detergent recommended for pressure washers only. Check that the detergent bottle or suction tube is properly connected. Clean the filter on the detergent suction tube by running warm water through it to remove any debris. If the detergent suction tube is damaged or clogged, remove the obstruction or replace the tube. Also, blow out or remove any debris from the discharge nozzle.
L
Luis WilliamsAug 31, 2025
What to do if my Black & Decker BEPW1750 Pressure Washer motor buzzes but doesn't run?
- J
  Joshua RamirezAug 31, 2025
  If your Black & Decker Pressure Washer motor buzzes but fails to run, ensure that only the pressure washer is running on the circuit to verify the supply voltage is above the minimum. Turn the unit off, squeeze the trigger on the spray wand to release any residual pressure, and then turn the unit back on. Plug the unit directly into the outlet to avoid voltage loss from an extension cord. If the cleaner has not been used for a long period, contact your local dealer.
D
Dalton FlowersAug 29, 2025
Why does my Black & Decker Pressure Washer pressure go up and down?
- A
  Anne ThompsonAug 29, 2025
  If the output pressure of your Black & Decker Pressure Washer varies, ensure you have enough inlet water supply by turning the water on full force and checking the hose for leaks and kinks. Also, check that the hoses and fittings are airtight, and purge the pump by turning the machine off and squeezing the trigger gun until a steady flow of water emerges from the nozzle. Clean the water inlet screen by rinsing it off with water, and clear any obstructions from the discharge nozzle.
G
Gary AlvarezAug 27, 2025
Why is my Black & Decker Pressure Washer not reaching high pressure?
- L
  Loretta ClarkAug 28, 2025
  If your Black & Decker Pressure Washer isn't reaching high pressure, fully open the water valve and check the water hose for any kinks, leaks, or blockages that may be restricting the water supply. Clean the water inlet filter by removing it and rinsing it. If the nozzle is worn, replace it with a new one. Ensure hoses and fittings are airtight, and purge the pump by turning off the machine and squeezing the trigger gun until water flows steadily from the nozzle. If the unit is not properly self-primed, refer to Self Priming under Assembly.
P
Patricia DavisAug 26, 2025
How to fix garden hose connection leaks on Black & Decker BEPW1750?
- J
  Justin HoffmanAug 27, 2025
  Garden hose connection leaks are often due to loose fittings (tighten the fittings) or a missing/worn rubber washer (replace the washer in the hose adapter).
P
Pamela RandallAug 25, 2025
What to do if Black & Decker BEPW1750 Pressure Washer motor buzzes but fails to run?
- A
  adam32Aug 25, 2025
  If the motor buzzes but doesn't run, it could be due to supply voltage being below the minimum (verify that only the pressure washer is running on the circuit), the system having residual pressure (turn the unit off, squeeze the trigger on the spray wand to release pressure, then turn the unit on), or voltage loss due to an extension cord (plug directly into the outlet).
M
Mrs. Brenda Zavala MDAug 22, 2025
Why Black & Decker BEPW1750 Pressure Washer motor does not start?
- A
  Amanda GibsonAug 22, 2025
  The motor may not start due to several reasons: the unit isn't plugged in (plug in the power cord); the ON/OFF switch is in the OFF position (turn the switch to the “ON” position); or the wand trigger isn't being squeezed (squeeze the trigger with the switch in the “ON” position).