Why is my Black & Decker CLM3820 not picking up clippings?
Your Black & Decker lawn mower might not be picking up clippings because the chute is clogged. Turn the mower off, remove the safety key and battery pack, and clear any grass clippings from the chute. Alternatively, you might be cutting too much grass at once. Try raising the cutting height. Also, ensure you empty the bag frequently, as a full bag can prevent proper pickup.
How to fix ragged finish or motor labours on Black & Decker CLM3820?
If your Black & Decker lawn mower leaves a ragged finish or the motor labours, first ensure the battery is fully charged by pressing the state of charge button and charging if needed. Then, turn off the mower, remove the safety key and battery pack, and check the blade for sharpness and the deck and discharge chute for clogs. Finally, consider raising the cutting height if it's set too low for the grass.
Why does my Black & Decker Lawn Mower leave a ragged finish?
If your Black & Decker Lawn Mower leaves a ragged finish or the motor labours, ensure the battery is fully charged by pressing the state of charge button and charging if needed. Also, release the bail handle to turn the mower off, remove the safety key and battery pack, then turn the mower over to check the blade sharpness and for any clogging in the deck and discharge chute. Keeping the blade sharp is important. Additionally, the wheel height adjustment might be too low for the grass condition, so raise the cutting height.
How to fix a noisy and vibrating Black & Decker Lawn Mower?
If your Black & Decker Lawn Mower is abnormally noisy and vibrates, release the bail handle to turn the mower off, remove the safety key and battery pack. Turn the mower on its side and check the blade for any bends or damage. If damaged, replace it with a Black & Decker replacement blade. If there is no visible damage, release the bail handle, remove the safety key and battery pack, and then remove the blade. Rotate the blade through 180 degrees and re-fit.
Why is my Black & Decker CLM3820 so hard to push?
If your Black & Decker lawn mower is hard to push, try raising the cutting height to reduce deck drag on the grass. Also, check each wheel to ensure it rotates freely.
What to do if my Black & Decker Lawn Mower is abnormally noisy and vibrates?
If your Black & Decker lawn mower is making unusual noises and vibrating, turn it off, remove the safety key and battery pack. Check the blade for bends or damage. Replace it if damaged with a Black & Decker replacement blade. If there's no visible damage, remove the blade, rotate it 180 degrees, and re-fit it. If the mower still vibrates after these steps, return the mower to an authorized Black & Decker service center.
What to do if my Black & Decker Lawn Mower is not picking up clippings?
If your Black & Decker Lawn Mower isn't picking up clippings, there are several potential causes. First, the chute might be clogged; in this case, release the bail handle to turn the mower off, remove the safety key and battery pack, and clear the chute of grass clippings. Alternatively, you might be cutting too much grass at once, so raise the cutting height of the wheels. Finally, the bag might be full, so try emptying it more often.
Why is my Black & Decker Lawn Mower too hard to push?
If your Black & Decker Lawn Mower is too hard to push, raise the cutting height to reduce deck drag on the grass. Also, check each wheel to ensure it rotates freely.
General| Power Source | Battery |
|---|---|
| Cutting Width | 38 cm |
| Cutting Width (inches) | 15 inches |
| Cutting Heights | 6 |
| Collection Capacity | 40 L |
| Grass Collection | Yes |
| Grass Collection Capacity | 40 L |
| Deck Material | Plastic |
| Cutting Height Adjustment | Single lever |
| Additional Features | Foldable |
To Next Page
