To Next PageTo Next PageHow to fix a Black+Decker Dishwasher that doesn’t start?
If your Black+Decker Dishwasher doesn't start, first check the fuse or circuit breaker and replace or reset it, removing any other appliances from the same circuit. Ensure the dishwasher is turned on, the door is securely closed without obstructions, and the power cord is properly plugged into the wall socket.
Why are the dishes not clean in my Black+Decker Dishwasher?
If your Black+Decker dishwasher isn't cleaning dishes properly, it might be due to several reasons. Ensure dishes are loaded correctly, select a more intensive wash program, use enough detergent or change your detergent if needed. Also, rearrange items blocking the spray arms and clean/fit the filter combination correctly, including cleaning the spray arm jets.
Why are the dishes not drying in my Black+Decker Dishwasher?
If your Black+Decker dishwasher isn't drying dishes, ensure proper loading as suggested in the directions. Increase the amount of rinse-aid by refilling the dispenser. Avoid emptying the dishwasher immediately after washing; instead, open the door slightly and wait until the dishes are barely warm. Note that short wash programs may not have sufficient drying times, so choose a longer cycle. Also, plastic items might not dry well in a dishwasher.
What to do if water is not pumped from Black+Decker Dishwasher?
To resolve water not being pumped from your Black+Decker dishwasher, inspect the drain hose for any kinks. Also, check the coarse filter for clogs. Ensure your kitchen sink is draining correctly; if the sink or plumbing is the issue, contact a plumber.
Why are there suds in my Black+Decker Dishwasher?
If there are suds in your Black+Decker dishwasher, it might be because you used the wrong type of detergent. Make sure you're using dishwasher detergent. If you used regular soap, open the door to let the suds evaporate, add a gallon of cold water, close the door, and run a soak cycle to drain. Repeat if needed. Also, wipe up any spilled rinse-aid immediately.
How to prevent cloudiness on glassware in Black+Decker Dishwasher?
If you notice cloudiness on glassware in your Black+Decker dishwasher, it could be due to soft water combined with too much detergent. Try using less detergent if you have soft water and select a shorter wash cycle to clean the glassware effectively.
How to remove white film from Black+Decker Dishwasher?
To address a white film on the inside surface of your Black+Decker dishwasher, use a damp sponge to clean the interior. You can use a mild soap and water solution, but ensure all soap residue is wiped away after cleaning.
How to remove black marks from dishes in Black+Decker Dishwasher?
If you find black or gray marks on dishes from your Black+Decker dishwasher, it's likely due to aluminum utensils rubbing against them. Use a mild abrasive cleaner to remove these marks.
How to stop knocking noise in Black+Decker Dishwasher?
A knocking noise in the wash cabinet of your Black+Decker dishwasher indicates that the spray arm is hitting against an item. To resolve this, interrupt the program and rearrange the items obstructing the spray arm.
How to fix rattling noise in Black+Decker Dishwasher?
A rattling noise in the wash cabinet of your Black+Decker dishwasher is caused by items not being dishwasher safe. To solve this, interrupt the program and rearrange the items of crockery.
General| Capacity | 8 place settings |
|---|---|
| Color | Black |
| Voltage | 120V |
| Wash Cycles | 6 |
| Power Cord Length | 60 inches |
| Included Accessories | Cutlery Basket |
General safety precautions for operating electrical appliances.
Details on grounding and power supply for safe operation.
Guidance on extension cords and proper electrical connection.
Steps and warnings for installing the dishwasher.
Instructions for connecting the dishwasher to the water supply.
Steps for properly connecting the drain hose to various outlets.
Explanation of buttons and indicators on the dishwasher control panel.
Overview of different wash cycles, times, and resource usage.
Initial troubleshooting steps for common operational issues.
