Blanco BFD10XP User Manual

11
EN
10
EN
5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER
NB:
You can deactivate the “Salt” and “Rinsing” product lights if you are using multi-purpose
products; this is done by using the “S
ET ” button (page 17)
• Loading the multi-purpose tablet dispenser
To assist in loading the detergent, the distributor is situated on the front of the upper basket. It is
compatible with all the products recommended for dishwashers.
• Place the tablet in the external compartment (Fig 04 on previous page) or, for optimum
results, pull out the distributor’s drawer and lay the tablet inside
(Fig 05 on previous page).
- Close the dispenser.
• FOR MULTI-PURPOSE PRODUCTS (Water hardness less than at 25°F)
• Your appliance automatically adapts to using multipurpose products when
the water hardness is less than 25°F.
TTeessttiinngg ssttrriipp
HHaarrddnneessss
0-10°F 10-18°F 18-25°F
MMuullttii--ppuurrppoossee
pprroodduuccttss FFuunnccttiioonn DDeeaaccttiivvaatteedd
MMuullttii--ppuurrppoossee
pprroodduuccttss SSppaarrkklliinngg CClleeaann
MMuullttii--ppuurrppoossee
pprroodduuccttss
EExxttrraa DDrryy
H0
OFF
H0
H0
OH
OH
HI
OFF
HI
HI
OH
OH
H2
OFF
H2
H2
OH
OH
5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER
Important:
It is very important to set the water softener correctly.
- If the setting is too low, there is the risk of chalky marks appearing.
- if the setting is too high, there is the risk of causing clouding of the glasses.
If you relocate, adjust the water softener setting as required.
•
SSttaannddaarrdd wwaasshhiinngg
tablets
Non-multipurpose tablets should be placed in the external compartment (Fig 04) or, for optimum
performance, pull out the dispenser drawer and lay the tablet inside (Fig 05).
• Powders or liquids (Fig 13)
Fill at least up to the minimum mark for slightly dirty crockery and to the maximum mark for dirty
crockery. If the crockery is very dirty and for programmes with a pre-wash we recommend that you
add 5g of detergent (a dessert spoonful) into your dishwasher’s tub in accordance with the pro-
grammes table.
Important:
Keep these products out of children’s reach and away from dampness.
Only use products specially designed for dishwashers.
Fig. 04 Fig. 05Fig. 03
• FOR STANDARD WASHING PRODUCTS
• Your machine must be specially adjusted to use
ssttaannddaarrdd wwaasshhiinngg
products.
Factory setting :
HH44
• Proceed as follows to adjust the water softener on the control panel:
— This feature is adjusted using the “SET” ; button; hold down this but-
ton to access the menu. Then press twice to set the softener level.
— The softener level is then shown on the screen from
HH00
to
HH66
. The
default level is
HH44
..
— To change the level from
HH00
to
HH66
, depending on the water hardness, press either arrow button
several times the screen displays the level you have set.
— The setting is validated automatically after 10 seconds if the
“ SET ” button in not pressed again.
— Pressing “S
ET” enables you to validate the setting and move on to the next parameter.
TTeessttiinngg ssttrriipp
HHaarrddnneessss
0-10°F 10-18°F 18-25°F
25-40°F
40-55°F 55-70°F > 70°F
TTrraaddiittiioonnaall
pprroodduucctt
HIH0 H2 H3 H4 H5 H6
45°C
7
0°C 65°C 55°C 45°C
• Proceed to set the water softener
— This feature is adjusted using the “SET” ; button; hold down this button to access the menu. Then
press twice to set the softener level.
— The softener level is then shown on the screen from
HH00
to
HH66
. The default level is
HH44 ..
— In order to use multi-function tablets, you need to adjust the setting. To do this, press either arrow but-
ton several times until you have selected
HH00
or
HH II
or
HH22
depending on the water hardness.
• Proceed to set the “ ” function (optional)
— Hold down the “SET
” button until the “AUTO 4/1” light flashes, then press one or other of the
selection buttons
.
— : deactivates the “A
UTO 4/1” option.
—
: corresponds to activation of the “AUTO 4/1” function with the setting for
““SSppaarrkklliinngg CClleeaann””
.
.
TThhiiss eennaabblleess yyoouu ttoo pprriioorriittiissee aa bbrriilllliiaanntt ffiinniisshh ffoorr yyoouurr ccrroocckkeerryy..
— : corresponds to activation of the “AUTO 4/1” function with the setting for
““EExxttrraa DDrryy””
.
““EExxttrraa ddrryy”” eennhhaanncceess tthhee ddrryyiinngg rreessuullttss iiff ppeerrffoorrmmaannccee iiss rreedduucceedd..
— The se
tting is validated automatically after 10 seconds if the
“ SET ” button in not pressed again.
— The “A
UTO 4/1 ” light then illuminates permanently if this option has been selected.
45°C
7
0°C 65°C 55°C 45°C

Blanco BFD10XP Specifications

General

Brand	Blanco
Model	BFD10XP
Category	Dishwasher
Language	English