Blastrac 2-20DT - User Manual

Questions and Answers

L
Lori BarnettAug 15, 2025
Why is my Blastrac 2-20DT blasting performance reduced?
- M
  martinezdavidAug 15, 2025
  Reduced blasting performance in your Blastrac industrial equipment can stem from several causes. It could be due to an inadequate abrasive supply, so you should clean the wire mesh and top up the abrasive if needed. Another cause could be contaminated abrasive, in which case you should check the dust collection system. Also, check and clean any blockages in the feed spout or magnetic valve. Finally, inspect the blast wheel or control cage for wear and replace the tune-up kit if necessary. You may also need to check the adjustment of the magnetic valve.
T
Terri WalkerAug 18, 2025
What to do if abrasive is escaping from Blastrac 2-20DT Industrial Equipment?
- D
  Dr. Riley VillanuevaAug 19, 2025
  If abrasive is escaping from your Blastrac industrial equipment, several factors could be responsible. Begin by checking all seals and replacing them if necessary. Ensure the magnetic seals are correctly adjusted. Also, worn magnetic and/or brush seals can cause this issue, so replace them if needed. Finally, a worn tune-up kit can be the culprit, so consider replacing it.
M
Mary WashingtonAug 21, 2025
How to reduce excessive vibration in Blastrac Industrial Equipment?
- M
  Marc VasquezAug 21, 2025
  Excessive vibration in your Blastrac industrial equipment may be due to a blast wheel worn irregularly or an imbalance caused by a worn or broken wheel. Replacing the tune-up kit may address a worn blast wheel. If there is an imbalance, replace the tune-up kit and remove all broken parts from the machine.
A
Alan FisherAug 26, 2025
Why is my Blastrac Industrial Equipment making unusual noises?
- J
  Joshua ScottAug 26, 2025
  Unusual noises from your Blastrac industrial equipment can arise from various issues. Check the alignment of the rotating parts, such as the blast wheel and control cage, as too little play or poor alignment can cause noise. Ensure all screws and parts are tightly fixed, as loose set screws can also be a source. If you hear squeaking wheels, replace them. Finally, a seizing motor can also cause unusual noises, so replace the motor if necessary.
J
joshua98Aug 28, 2025
How to fix contaminated abrasive in Blastrac 2-20DT Industrial Equipment?
- V
  Vanessa CooperAug 28, 2025
  If the abrasive in your Blastrac industrial equipment is contaminated, it could be due to the dust collector not generating enough suction power, causing dust to remain in the abrasive. Check the dust collector, including the filter cartridges, dust hopper, and seals. Also, check and clean the dust hose if it's clogged, or replace it if it's ripped or damaged.
J
James MurrayAug 31, 2025
What to do if Blastrac 2-20DT Industrial Equipment is not moving?
- M
  mbrownSep 1, 2025
  If your Blastrac industrial equipment isn't moving, first ensure the travel speed isn't too low and increase it if needed. If the blast head is catching on the floor, shut down the machine and adjust the height. Finally, check the chain drive, as a broken or disconnected drive unit could be the problem.
J
James GardnerSep 4, 2025
Why does the blast wheel motor switch off during operation of Blastrac 2-20DT Industrial Equipment?
- M
  Mr. Kevin RiveraSep 4, 2025
  If the blast wheel motor switches off during operation of your Blastrac industrial equipment, the connection cable or the cables connecting the units (travel motor, etc.) may be defective, so replace the cable(s).
B
Brandon BairdSep 7, 2025
How to prevent excessive wear in blast housing of Blastrac 2-20DT?
- E
  Erin HayesSep 7, 2025
  Adjust the blast pattern by correcting the setting of the control cage.
I
ihallSep 12, 2025
What to do if Blastrac Industrial Equipment blast wheel motor does not switch on?
- C
  Christopher HuntSep 12, 2025
  If the blast wheel motor on your Blastrac industrial equipment doesn't switch on, check the mains power supply and switch on the motor protection switch again.