9
• By repeatedly pressing the Program selection
button the water hardness can be selected:
H1->H2->H3->H4->H5->H6. The control lamps
indicate the selection (see below table).
• The setting is automatically saved after a few
seconds; alternatively end the setup with the
Power button.
Water hardness
Water hardnessWater hardness
Water hardness
Setting
SettingSetting
Setting
Control lamps
Control lamps Control lamps
Control lamps
lights
lightslights
lights
Salt cons.
Salt cons.Salt cons.
Salt cons.
/ c
/ c/ c
/ cycle
ycleycle
ycle
°dH
°dH°dH
°dH
Mmol/l
Mmol/lMmol/l
Mmol/l
0-5 0-0.94 H1 Rapid 0 g
6-11 1.0-2.0 H2 90 Min. 9 g
12-17 2.1-3.0 H3 90 Min + Rapid 12 g
18-22 3.1-4.0 H4 Eco 20 g
23-34 4.1-6.0 H5 Eco + Rapid 30 g
35-55 6.1-9.8 H6 Eco + 90 Min. 60 g
NOTE
NOTENOTE
NOTE:
::
:
°dH: German degree of hardness
Factory setting: H3
Fill in the salt
Fill in the saltFill in the salt
Fill in the salt
CAU
CAUCAU
CAUTION:
TION:TION:
TION:
• Only refill the salt container when the salt warning
lamp is lighting.
• During filling the salt container, salt and water can
escape. Start a program immediately after you
have filled the container to prevent corrosion.
• Remove the lower basket and unscrew the lid of
the salt container.
• Add about 1.5 kg of salt by using the supplied
funnel tube.
• Full fill the salt container with water (just before
the first use).
• Screw the lid firmly on again after filling the con-
tainer.
• Depending on salt resolution, the warning lamp
usually disappears immediately after filling.
B
BB
B.
. .
.
Fill the rinse aid dispenser
Fill the rinse aid dispenserFill the rinse aid dispenser
Fill the rinse aid dispenser
Function of rinse aid
Function of rinse aidFunction of rinse aid
Function of rinse aid
The rinse aid is automatically added during the final
rinse, ensuring thorough rinsing and a spot and
streak free drying.
When to refil
When to refilWhen to refil
When to refill the rinse aid dispenser
l the rinse aid dispenserl the rinse aid dispenser
l the rinse aid dispenser
As long as the corresponding
message does not light up in the
display, you can estimate the
amount of remaining rinse aid to the optical level
indicator (D
DD
D) next to the dispenser.
When the rinse aid dispenser is full, the indicator is
completely dark. If the rinse aid diminishes, the size
of the black dot changes as shown below. In order to
avoid spotting, the rinse aid level must not drop be-
low ¼.
full ¾ full
½ full
¼ full empty
Fill in the rinse aid
Fill in the rinse aidFill in the rinse aid
Fill in the rinse aid
• To open the dispenser screw the lid counter-
clockwise to the open position and remove the lid.
• Add the rinse aid into the dispenser, being careful
not to overfill. The dispenser contains approx.
110 ml.
• Before closing the appliance door, put on the lid in
the open position back and turn it clockwise to the
closed position.
NOTE
NOTENOTE
NOTE:
::
:
Remove spilled rinse aid with an absorbent cloth to
avoid excessive foaming during the next rinse.
Adjusting the rinse aid dosage
Adjusting the rinse aid dosageAdjusting the rinse aid dosage
Adjusting the rinse aid dosage
When forming spots and the dishes dries poorly,
increase the added amount of rinse aid. You can set
the amount of addition between level 1 (min.) and
level 6 (max.).
To Next Page
Loading...
