BorMann BBC2500 - Advanced Operations and Maintenance; Charging Completion & Testing; Battery Care and Cleaning; Troubleshooting Guide

EN
WWW.BORMANNTOOLS.COM
6
Fault Possible cause Remedy
Equipment does
not charge up
- Charger clamps connected incorrectly
- Contact between the charger clamps
- Baery defecve
- Connect the red clamp to the posive pole
and the back clamp to the bodywork
- Prevent contact
- Have the baery checked by an expert and replace it if necessary
The charging current should be 1/10 to 1/6 of the baery capacity.
Note! Gases are released during the charging process. It is essenal that you venlate the rooms well.
As long as the equipment is charging, the LCD display shines green. If charging is complete, the LCD display shines blue (BBC4000)
Finishing charging the baery
• Pull the plug out of the socket
• First disconnect the black charging cable from the bodywork.
• Then release the red charging cable from the posive pole on the baery.
• Important! In case of posive earthing, rst disconnect the red charging cable from the bodywork and then the black charging cable from the baery.
• Screw or push the baery stoppers back into posion (if there are any).
Baery tester for 12V baeries for BBC4000
Connect the charger to the baery. The LCD symbol “H” (Fig. B) shows the charge status (1 increment = 25%). The baery voltage is shown on the LCD dis-
play.
Overload cut-out
The charger is equipped with electronic protecon against overload, short circuit and swapped poles. One or more ne fuses are also ed. If the fuse suers
a defect it must be replaced by a new fuse with the same amp value. If necessary, please contact our customer service center.
Maintenance and care of the Baery
• Ensure that your baery is always ed securely.
• A perfect connecon to the cable network of the electrical system must be ensured at all mes.
• Keep the baery clean and dry. Apply a thin coang of grease to the connecon terminals using an acid-free, acid-resistant grease (Vaseline).
• Check the level of the acid in baeries that are not maintenance-free versions approximately every 4 weeks and top up with dislled water if necessary.
Cleaning & Maintenance
Danger! Always pull out the mains power plug before starng any cleaning work.
• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with com-
pressed air at low pressure.
• We recommend that you clean the device immediately each me you have nished using it.
• Clean the equipment regularly with a moist
cloth and some so soap. Do not use cleaning agents or solvents; these could aack the plasc parts of the equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool increases the risk of an electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned o the charging terminals.
There are no parts inside the equipment which require addional maintenance.cloth and some so soap. Do not use cleaning agents or solvents; these could
aack the plasc parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an
electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned o the charging terminals.cloth and some so soap. Do not use
cleaning agents or solvents; these could aack the plasc parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an
electric tool increases the risk of an electric shock.
• The charger should be placed in a dry room for storage. Any corrosion must be cleaned o the charging terminals.
Troubleshoong
If the equipment is operated properly you should experience no problems with malfuncons or faults. In the event of any malfuncons or faults, please check
the following before you contact your customer services.
* The manufacturer reserves the right to make minor changes to product design and technical specicaons without prior noce unless these changes signif-
icantly aect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also
concern other models of the manufacturer's product line with similar features and may not be included in the product you just acquired.
* Please note that our equipment has not been designed for use in commercial, trade or industrial applicaons. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or for equivalent purposes.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspecon, repair or replacement work, including maintenance and
special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.