Bosch 22-180 H - Page 9

10 | English
1 609 92A 0B7 | (25.7.13) Bosch Power Tools
Assembly
Mounting the Protective Devices
 Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section “After-
sales Service and Application Service”.
Protection Guard for Grinding (Clamping Screw)
Place the protection guard 21 on the spindle collar. Adapt the
position of the protection guard to the requirements of the
work step and lock the protection guard 21 with the locking
screw 22.
 Adjust the protection guard in such a manner that
sparking is prevented in the direction of the operator.
Protection Guard for Cutting
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 23.
 Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 23 is mounted in the same
manner as the protection guard for grinding .
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 18 is
mounted in the same manner as the protection guard for
grinding.
Auxiliary Handle
 Operate your machine only with the auxiliary handle 3.
Screw the auxiliary handle 3 on the right or left of the machine
head depending on the working method.
Angle Grinder GWS ... 24-230
H
24-230
JH
26-180
H
Article number
3 601 ... H84 1.. H84 2.. H55 1..
Rated power input
W 2400 2400 2600
Output power
W 1600 1600 1700
Rated speed
min
-1
6500 6500 8500
Grinding disc diameter, max.
mm 230 230 180
Thread of grinder spindle
M 14 M 14 M 14
Thread length (max.) of grinder spindle
mm 25 25 25
Reduced starting current
–  –
Rotatable main handle
– ––
Weight according to EPTA-Procedure 01/2003
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
5.2
5.1
5.3
5.2
6.0
5.9
Protection class /II /II /II
Angle Grinder GWS ... 26-230
B
26-230
H
26-230
H
Article number 3 601 ... H56 3.. H56 1.. H56 L..
Rated power input
W26002600 2600
Output power
W17001700 1700
Rated speed
min
-1
6500 6500 6500
Grinding disc diameter, max.
mm 230 230 230
Thread of grinder spindle
M 14 M 14 M 14
Thread length (max.) of grinder spindle
mm 25 25 25
Reduced starting current
– ––
Rotatable main handle
 ––
Weight according to EPTA-Procedure 01/2003
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
6.2
6.1
6.1
6.0
6.1
6.0
Protection class /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
OBJ_BUCH-827-006.book Page 10 Thursday, July 25, 2013 3:44 PM
Ташев-Галвинг ООД
www.tashev-galving.com