10 | English
1 619 P13 237 | (18.3.15) Bosch Power Tools
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745:
Surface grinding: a
h
= 7.0 m/s
2
, K=1,5 m/s
2
,
Disk sanding: a
h
= 3.0 m/s
2
, K=1,5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Only for EC countries:
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 04.03.2015
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance. For addresses, see section
“After-sales Service and Application Service”.
Angle Grinder GWS ... 1400 C 14-125 CI 14-125 CIE 14-125 CIT 14-150 CI
Article number
3 601 ... H24 ... H24 ... H25 ... H29 ... H26 ...
Rated power input
W 1400 1400 1400 1400 1400
Output power
W 820 820 820 820 820
Rated speed
min
-1
11000 11000 11000 9300 9300
Speed control adjustment
min
-1
– – 2800 – 11000 ––
Grinding disc diameter, max.
mm 125 125 125 125 150
Thread of grinder spindle
M 14 M 14 M 14 M 14 M 14
Thread length (max.) of grinder spindle
mm 22 22 22 22 22
Kickback stop
–
Restarting Protection
–
Reduced starting current
Constant electronic control
Speed preselection
– – ––
Weight according to EPTA-Procedure
01/2003
– with vibration-damping auxiliary handle
– with standard-auxiliary handle
kg
kg
2.2
2.1
2.2
2.1
2.2
2.1
2.2
2.1
2.3
2.2
Protection class /II /II /II /II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_DOKU-28002-003.fm Page 10 Wednesday, March 18, 2015 2:05 PM
To Next Page
Loading...
