Bosch Blue Line Gen2 ISC-BPR2

To Next Page

Ligue todas as cablagens apenas a um circuito de

segurança de tensão extra baixa (SELV).

NOTE:

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

UL/C-UL

Perform Walk Test at least once a year.

Use only a Listed limited-power source.

The Listed control unit or a Listed burglary power supply must provide 4

hours (40 mAh) of standby power.

Install the unit in accordance with National Electrical Code NFPA 70 and

Part 1 of the Canadian Electrical code CSA C22.1.

Sluit alle bedrading uitsluitend aan op een

circuit met een extra lage veiligheidsspanning.

Prenez soin de connecter tous les câbles à un

circuit à très basse tension de sécurité (TBTS).

Alle Drähte sind ohne Ausnahme an

Niederspannung anzuschließen.

Collegare tutti i cavi esclusivamente a un circuito

SELV (circuito di sicurezza a bassissima tensione).

EN 50131-2-2 Grade 2

EN 50130-5 Environmental Class II

IP30 IK04 (EN 60529, EN 50102)

0 - 95% Relative Humidity

(0 - 85% UL/C-UL installations)

-30°C to +55°C

(-20°F to +130°F )

UL Listed installations,

the temperature

range is 0°C to +49°C

(+32°F to +120°F)

Pour les installations

certiées NFA2P,

Température de

fonctionnement

-10°C à +55°C

Conecte el cableado únicamente a un circuito

de seguridad para voltajes muy bajos (SELV).

SELV

Connect all wiring to a safety extra-low voltage (SELV)

circuit only.

Changes or modications not expressly approved

by Bosch Security Systems, Inc. can void the

user’s authority to operate the equipment.

Optional Brackets:

B328, B338, B335

INCERT B-509-0051/b

Certicat NF A2P 2620200001

2 boucliers NF324 - H58

Autosurveillance à l’ouverture

Immunité champ magnétique

Testé sans masque de vision verticale

www.afnor.org

www.cnpp.com

För svensk installationsanvisning se www.boschsecurity.se.

1 2 3

2,2 m - 2,75 m

(7.5 ft - 9 ft)

Recommended:

2,2m (7.5 ft)

Blue Line Gen2

PIR Motion Detector

ISC-BPR2-W12

en Installation Guide

Need help?

Do you have a question about the Bosch Blue Line Gen2 ISC-BPR2 and is the answer not in the manual?

Summary

Installation Safety and Compliance

General Safety and Interference Notes

Covers FCC compliance, radio frequency energy, and methods to correct interference.

UL;C-UL and European Standards

Details UL/C-UL requirements for power sources and installation, plus CE/EN standards.

Low Voltage and Safety Precautions

Emphasizes connecting wiring to Safety Extra-Low Voltage (SELV) circuits only.

Mounting and Bracket Options

Provides installation steps and lists optional mounting brackets.

Detector Operation and Wiring

Wiring and Power Specifications

Details terminal connections, power input requirements, and current draw.

LED Indicator and Walk Test

Explains the LED status indicator and the procedure for performing a walk test.

Detection Pattern and Dimensions

Illustrates the detector's coverage pattern and provides unit dimensions.