Operation
37
Climate 5000 L • Climate 5000i U/L – 6721841496 (2024/06)
Display of the wired room controller
Key to figure 4:
[1] Display of main operating modes
[2] Display of temperature and status
[3] Display time
[4] Timer display
Table 42 Symbols in the display
3.4 Remote control overview
Keys on remote control
Fig. 5
Table 43 Keys on remote control
Display of remote control
Fig. 6
Table 44 Symbols in the display
3.4.1 Using the remote control
The signal range is 8 m. If objects are in the way or certain fluorescent
lamps are used in the same room this can affect transmission of the
signal.
▶ Point the remote control towards the signal receiver window of the
device and press the desired key.
The device emits a beep when it receives a signal.
NOTICE
The remote control may be permanently prevented from working
correctly.
▶ Do not expose the remote control to direct sunlight.
▶ Do not leave the remote control near a heating appliance.
▶ Protect the remote control from moisture and impacts.
3.5 Setting the day and time
▶ Press the TIMER key until the timer display starts flashing.
▶ Select the current day with the . and / keys. The selected day
flashes.
▶ Press the TIMER or key to confirm the entry.
The selection jumps to the time.
▶ Press or hold the . or / key to set the time.
▶ Press the TIMER or key to confirm the entry.
To toggle between 12- and 24-hour display:
▶ Press/keep the TIMER and DAY OFF keys pressed simultaneously
for several seconds.
Pos. Symbol Explanation
1 Display of main operating modes
Operating mode: automatic mode
Operating mode: cooling mode
Operating mode: dehumidification mode
Operating mode: heating mode
Operating mode: Fan Mode
K Operating mode: On/Off
2 Display of temperature and status
Value display: shows the current fan speed. There are
several output stages (bars) and the AUTO setting for
automatic control
Value display: indicates the set temperature as
standard.
Infographic: keylock
Infographic: appliance 1/2
Infographic: Turbo cool/Turbo heat is active.
Infographic: room temperature
Infographic: automatic rotation is active.
Infographic: Follow me active.
3 Time display
Value display: indicates time.
4Timer display
Infographic: timer On/Off
Infographic: weekdays active
Infographic: day
Infographic: week
Pos. Key Function
1 K Switch on/off.
Mode Set operating mode.
Eco operation mode
2SET Select advanced operating functions.
OK Confirm choice.
Set timer.
. Increase temperature.
/ Reduce temperature.
3 Fan step
Indirect airflow is active (Wind avoid me).
Turbo Turbo cool/Turbo heat
LED Switch display of indoor unit and alarm buzzer on and
off (Mute Mode).
Clean Self-cleaning (I clean)
Pos. Symbol Explanation
1 Operating function: Sleep mode is active.
Operating function: Follow Me function is active
(Follow Me); temperature measurement at the
remote control.
Infographic: wireless control function
Infographic: battery status
2 Operating mode: automatic mode
Operating mode: cooling mode
Operating mode: dehumidification mode
Operating mode: heating mode
Operating mode: Fan Mode
3 Value display: shows the set temperature, fan speed
or (when timer is activated) the timer setting as
standard.
Infographic: transmission indicator; lights up when
the remote control sends a signal to the indoor unit.
Infographic: energy saving function active
1)
.
1) Not available for Duct type indoor unit.
Infographic: energy saving function active
1)
.
Infographic: ON/OFF timer active.
Infographic: noise reduction is active (Silent Mode).
Value display: shows the current fan speed. There are
several output stages (bars) and the AUTO setting for
automatic control
4 Infographic: Turbo cool/Turbo heat is active.
To Next Page
Loading...
