Operation
Climate 5000 L • Climate 5000i U/L – 6721841496 (2024/06)
38
3.6 Setting main operating mode
Depending on the indoor unit and configuration of the wired room
controller, not all operating modes may be available.
Turn unit on/off
▶ Press the K key to switch the device on or off:
The unit starts in the set operating mode or switches off. To protect
the unit it can only be switched back on after some time has passed.
Settings can also be made when the appliance is switched off. The
device saves the settings, and also retains them in the event of a power
failure.
Following a power failure the unit restarts automatically. This can lead to
conflicting readings on the displays which are resolved automatically
during operation.
Automatic mode
In automatic mode, the unit switches automatically between heating,
cooling, fan and dehumidification mode, depending on the set
temperature.
▶ Press the M key repeatedly until appears on the display.
▶ Press the . or / key to set the required temperature.
The fan speed cannot be adjusted in automatic mode.
Cooling mode
▶ Press the M key repeatedly until appears on the display.
▶ Press the key until the required air speed is reached.
▶ Press the . or / key to set the required temperature.
Dehumidification mode
▶ Press the M key repeatedly until appears on the display.
▶ Press the . or / key to set the required temperature.
The fan speed cannot be adjusted in dehumidification mode.
Heating mode
▶ Press the M key until appears on the display.
▶ Press the . or / key to set the required temperature.
▶ Press the key until the required air speed is reached.
If the outside temperature is very low, the heating capacity of the air
conditioning system may not be sufficient. We recommend connecting
additional heat sources.
Fan (Only) Mode
▶ Press the M key repeatedly until appears on the display.
▶ Press the key until the required fan speed is reached. AUTO can
be selected to enable automatic control.
The temperature cannot be adjusted or displayed in fan mode.
3.7 Setting the room temperature
▶ Press the . or / key to set the desired room temperature.
The setting is applied shortly afterwards.
The temperature cannot be adjusted in Fan Mode.
3.8 Setting timer
3.8.1 One-time ON/OFF timer
▶ Press the TIMER key repeatedly until the corresponding symbol
appears.
–ON timer: ON DAY
–OFF timer: OFF DAY
– ON and OFF timer: ON+OFF DAY
▶ Confirm with key.
The clock display starts flashing.
▶ Press the . or / key to set the desired ON/OFF time.
▶ Press the key again to save the setting.
The ON/OFF timer cannot be set at a secondary wired room controller.
3.8.2 Weekly ON/OFF timer
Setting timer
▶ Press the TIMER key until WEEK 1 appears in the display.
▶ Confirm with key.
▶ Press the . or / key to select the weekday.
▶ Confirm with key.
▶ Press the . or / key to set the desired ON time.
▶ Confirm with key.
▶ Press the . or / key to set the desired OFF time.
▶ Confirm with key.
Up to four times can be set.
▶ Repeat procedure every subsequent day of the week.
To delete the timer for the selected day:
▶ Press the DAY OFF key.
Activating the timer
▶ Keep pressing the TIMER key until WEEK 1 appears in the display.
The timer is now switched on. The unit is switched on or off at the
selected times and days.
Deactivating the timer
▶ Keep pressing the TIMER key until WEEK 1 disappears in the display.
To switch off the unit when the week timer is active:
▶ Briefly press K key.
The unit switches off until the next ON timer is reached.
▶ Hold the K key pressed for two seconds to switch off the unit and
deactivate the week timer.
Programming the switch-on delay
If week timer 1 is active and the ON time is to be delayed.
▶ Select week timer 1 with TIMER key.
▶ Press the DAY OFF key 2x until 1h appears on the display.
▶ Wait for a few seconds while the setting is saved.
The unit now starts the next activity cycle following a delay of 1 hour.
▶ Press the DAY OFF key 3x until 2h appears on the display.
The unit now starts the next activity cycle following a delay of 2 hours.
To Next Page
Loading...
