en Steam
20
The arrow of the water tank symbol $ will go out
and the water tank symbol ( will be lit. The
appliance will start. The start l stop LED will be lit.
The cooking time will count down on the display. The
amount of time a tankful of water will last varies
depending on the steam setting. If the water tank
runs out of water while the appliance is in operation,
the appliance is paused and the arrow of the water
tank symbol $ flashes. Fill the water tank with fresh
water up to the "max." mark and touch the
start l stop button to resume operation.
Notes
■ The steam setting can be changed at any time when
the appliance is in operation by pressing the
" button.
■ After cooking with steam, wipe out the drip channel
and the cooking compartment. ~ "After every
steam operation" on page 21
Setting the steam combination
Set t i ng t he st eam c ombi nat i on
With some types of heating, you can switch on the
steam function.
When you cook with steam assistance, steam is
introduced into the cooking compartment at various
intervals and with varying degrees of intensity. This
gives you a better cooking result.
Your food
■ Becomes crispy on the outside
■ Achieves a glossy surface
■ Is succulent and tender on the inside
■ Only undergoes a minimum reduction in volume
Combination options
■ ! Microwave
■ < Hot air
■ ( Grill
■ 4 Hot air grill
Exceptions:
! Microwave setting, 1000watts
< Hot air 40°C
Setting combination mode
Example: Hot air < 190ºC with steam setting 2.
1. Use the function selector to set the Hot air <
heating function.
A default value for the temperature will be displayed.
2. Turn the rotary selector to set the desired
temperature.
3. Touch the Steam button " until the required setting
has been selected on the display.
The water tank symbol $ will appear on the display.
4. Refill water tank.
5. Touch the start l stop button.
The appliance will start and the start l stop LED will
be lit.The cooking time will start counting down.
Notes
■ If the water tank runs out of water during cooking,
the appliance will continue cooking, but without
steam assistance. No indicator will appear on the
display.
■ Opening the appliance door affects the cooking
result. Always keep the appliance door closed when
cooking.
The cooking time has elapsed
A signal sounds and the start l stop symbol stops
lighting up. Combination mode has finished. Touch any
field to end the acoustic signal.
Changing the steam level
Touch the " field until the required level is selected in
the display.
Note: Touch the field multiple times switches through
the levels from the highest to the lowest level. After the
lowest level, the steam function is deactivated.
Touching again activates the steam function, starting
with the highest level.
Pausing the operation
1. Touch the start l stop field or open the appliance
door.
The operation is suspended and the
start l stop LED flashes.
2. Close the appliance door.
3. Touch the start l stop field.
The operation is continued and the start l stop LED
lights up.
Stopping the appliance from heating
Turn the function selector to the "Off" position.
The appliance will stop heating and all the settings will
be cleared.
Note: The fan may continue to run after the appliance
has been paused or stopped.
Filling the water tank
Filling t he wat er t ank
The water tank is located to the right behind the tank
cover, below the appliance door. Before starting an
operation with steam, open the tank cover and fill the
water tank with water.
Ensure that the water hardness range has been set
correctly. ~ "Basic settings" on page 28
:Warning – Risk of injury and fire!
Only fill the water tank with water. Do not pour any
flammable liquids (e.g. alcoholic drinks) into the water
tank. Due to hot surfaces, vapours from flammable
liquids may catch fire in the cooking compartment
(explosion). The appliance door may spring open. Hot
steam and jets of flame may escape.
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(>40mg/l) or other liquids.
Only use fresh, cold, non-carbonated tap water or
softened water.
Steam en
21
Notes
■ If your water is very hard; we recommend that you
use softened water.
■ If you use only softened water, you can set your
appliance to the "softened" water hardness range.
1. Briefly press on the centre of the tank cover.
The tank cover will open. The drip tray (left) and
water tank (right) can now be accessed.
2. Remove the water tank from the tank recess.
3. Fill the water tank with cold water up to the "max."
mark.
4. Place the water tank back into the tank recess and
slide it in fully.
5. Close the tank cover.
The steam function is ready to use.
Refilling the water tank
The way the appliance responds if the water tank runs
dry when the appliance is in operation depends on what
operating mode it is in:
■ Steam-assistance mode: The appliance is stopped
and a message appears on the display.At the
highest steam setting, a tankful of water will last
approx. 30-40 minutes; at the lower steam settings,
it will last much longer.
■ Steam-assistance with microwave: The appliance is
stopped. A tankful of water will last approx.
50 minutes.
■ Steam-assisted hot-air or grill mode: The appliance
continues to run in hot-air or grill mode; no message
appears on the display. At the highest steam setting,
a tankful of water will last approx. 3 hours; at the
lower steam settings, it will last much longer.
■ Steam-assisted air recirculation grill mode: The
appliance continues to run in air recirculation grill
mode; no message appears on the display. A tankful
of water will last approx. 9 hours.
Note: Actual times may vary from those specified.
Refill the water tank up to the "MAX" mark.
1. Open the control panel.
2. Remove and refill the water tank.
3. Insert the filled water tank and close the control
panel.
After every steam operation
Moisture remains in the cooking compartment. Carefully
wipe out the drip channel and the cooking
compartment. Each time you cook using steam, we
recommend that you run the Rinse cleaning function !
afterwards. Then empty and dry the water tank and drip
tray.
Note: Remove limescale marks with a cloth soaked in
vinegar, then wipe with clean water and dry with a soft
cloth.
Rinsing
To ensure that your appliance stays clean, you can
pump water through the pipe system. The water is then
drained to the drip tray.
Note: After rinsing, there can be dissolved lime
particles in the drip tray. This is normal and does not
affect operation.
1 2
To Next Page
Loading...
