en Steam
22
Starting
1. Use the function selector to select the rinse cycle !.
The duration of the programme will be displayed.It
cannot be changed.
2. Open the tank cover.
3. Remove and empty the drip tray.
4. Slide the empty drip tray in fully.
5. Remove water tank and drain any residual water.
Rinse out water tank thoroughly and fill with fresh
water.
6. Slide the water tank in fully.
7. Close the tank cover.
8. Touch the start l stop button.
Water is pumped through the pipes.The time
remaining will count down on the display. An audible
signal will sound once this time has elapsed. Empty
the drip tray.
Emptying the water tank
1. Briefly press on the centre of the tank cover.
The tank cover folds upwards.
2. Remove the water tank.
3. Carefully remove the lid for the water tank.
4. Empty the water tank, clean it with detergent and
then rinse it thoroughly with clean water.
5. Dry all parts with a soft cloth.
6. Rub the seal on the lid until dry.
7. Allow the water tank to dry with the lid open.
8. Place the lid on the water tank and push down on it.
9. Slide the water tank in fully.
10. Close the tank cover and briefly press on the centre
of it.
The tank cover is locked.
Caution!
■ Do not dry the water tank in the hot cooking
compartment. This will damage the water tank.
■ Do not clean the water tank in the dishwasher. This
will damage the water tank.
Cleaning the drip trough
1. Allow the appliance to cool down.
2. Open the tank cover.
3. Remove the water tank and drip tray.
4. Wipe around the drip trough ‚ underneath the
cooking compartment with a sponge cloth (fig. !).
Drying the cooking compartment
Dry the cooking compartment after operation to ensure
that no moisture remains.
Heating up the cooking compartment
To dry, heat up the cooking compartment so that the
moisture in the cooking compartment evaporates. Then
open the appliance door to allow the steam to escape
from the cooking compartment.
1. Allow the appliance to cool down.
2. Remove the worst dirt from the cooking
compartment immediately and wipe away moisture
from the cooking compartment floor.
3. Use the function selector to select Hot air grill 4
4. Touch 0 twice.
The cooking time symbol y is highlighted in the
display.
5. Use the rotary selector to set a cooking time of
15minutes.
6. Press start l stop to start the operation.
The drying function starts and ends automatically
after 15minutes.
7. Open the appliance door and leave it open for 1to
2minutes so that the moisture in the cooking
compartment can escape.
Drying the cooking compartment by hand
1. Allow the appliance to cool down.
2. Remove any food remnants from the walls of the
cooking compartment.
3. Dry the cooking compartment with a sponge.
4. Leave the appliance door open for 1hour so that the
cooking compartment dries completely.
D
1
Automatic programmes en
23
PAutomatic programmes
Aut omat i c pr ogr ammes
You can prepare food really easily using the automatic
programmes. You select the programme and enter the
weight of your food. The automatic programme then
applies the most suitable settings. You can select from
30 programmes.
Notes
■ Take the food out of its packaging and weigh it. If it
is not possible to enter the exact weight, you should
round it up or down.
■ Place the food in the cold cooking compartment.
■ For the programmes, always use microwaveable,
heat-resistant cookware, for example made of glass
or ceramic. Observe the accessories tips in the
programme table.
■ For an optimal cooking result, use food that is in
good condition and chilled meat only. For frozen
food, use food straight out of the freezer only.
Setting a programme
Example in diagram: Programme 3with a weight of
1kg.
1. Set the function selector to % automatic
programmes.
The first programme number and weight suggestion
are shown in the display.
2. Use the rotary selector to select programme number
3.
3. Touch h.
The weight setting is highlighted in the display.
4. Use the rotary selector to set the weight to 1kg.
The appliance automatically sets the right cooking
time for that weight.
5. Touch start l stop.
The programme will start. The cooking time visibly
counts down and the temperature bar and the
start l stop LED light up.
Notes
■ Before starting you can use % and ~/1 to switch
between programmes and weight.
■ Once you have started the programme, the
programme number and weight cannot be changed.
You can check the set weight by touching ~/1.
The programme has ended
An audible signal sounds. The programme has finished;
the appliance stops heating.
Turn the function selector to the off position.
Changing the programme
1. Touch the start l stop field for approx. four seconds.
The programme is reset.
2. Select a new programme.
Pausing the operation
1. Touch the start l stop field or open the appliance
door.
The operation is suspended and the
start l stop LED flashes.
2. Close the appliance door.
3. Touch the start l stop field.
The operation is continued and the start l stop LED
lights up.
Stopping the appliance from heating
Turn the function selector to the "Off" position.
The appliance will stop heating and all the settings will
be cleared.
Note: The fan may continue to run after the appliance
has been paused or stopped.
To Next Page
Loading...
