Bosch D7412G - Page 5

EN | 5
D9412G/D7412G | Operation & Installation Guide |
Bosch Security Systems | 10/03 | 43488E
Table of Contents
Figures
Figure 1: System Configuration ........................................ 11
Figure 2: Enclosure Mounting ........................................... 17
Figure 3: Ground Fault Detect .......................................... 18
Figure 4: Reset Pin .............................................................. 19
Figure 5: Non-Power Limited Wiring ............................... 22
Figure 6: Charging and Battery LEDs ............................23
Figure 7: Relays for Terminals 7, 8, and Ground Start26
Figure 8: RJ31X Wiring.......................................................27
Figure 9: Phone Connector, Phone LED, and
Operation Monitor LED Locations ................27
Figure 10: Phone Monitor Select ..................................... 29
Figure 11: D928 Dual Phone Line Switcher................. 30
Figure 12: On-Board Point Sensor Loop Wiring .......... 33
Figure 13: Wiring for Installation Using the Ademco
AB-12 Bell/Housing ........................................35
Figure 14: Connecting the D8125 POPEX to the
D9412G Panel .................................................39
Figure 15: Connecting the D8125 POPEX to the
D7412G Panel .................................................40
Figure 16: Program Record Sheet ................................... 42
Figure 17: D8128D OctoPOPIT Layout .........................43
Figure 18: Connecting D8128D OctoPOPITs to the
D9412G ..............................................................45
Figure 19: Connecting D8128D OctoPOPITS to the
D7412G .............................................................46
Figure 20: Wiring Multiple D81282Ds Using Molex
Connectors ........................................................ 47
Figure 21: D8128D OctoPOPIT Sensor Loops ............48
Figure 22: D8129 Connections to the D9412G .........50
Figure 23: D8129 Connections to the D7412G .......... 50
Figure 24: D811 Module Wiring to the D7412G .........52
Figure 25: D811 Module Wiring to the D9412G ........52
Figure 26: Power at Command Centers ........................54
Figure 27: Keyswitch Wiring .............................................55
Figure 28: D9133 Jumper Settings .................................58
Figure 29: D9133TTL-E Jumper Settings .......................59
Figure 30: Reset Pin ............................................................ 61
Figure 31: Programmer and Accessory Connections . 61
Figure 32: D9412G Faceplate .........................................63
Figure 33: D7412G Faceplate ..........................................64
Figure 34: D9412G System Wiring Diagram, 1 of 3 .65
Figure 35: D9412G System Wiring Diagram, 2 of 3 .66
Figure 36: D9412G System Wiring Diagram, 3 of 3 .67
Figure 37: D7412G System Wiring Diagram, 1 of 3 ..68
Figure 38: D7412G System Wiring Diagram, 2 of 3 ..69
Figure 39: D7412G System Wiring Diagram, 3 of 3 ..70
Tables
Table 1: Manual Organization ............................................. 7
Table 2: Related Documentation ........................................ 8
Table 3: Text Type Styles ...................................................... 8
Table 4: 9000G Series Panel Differences .................... 11
Table 5: Specifications ....................................................... 12
Table 6: Compatible Accessories ..................................... 13
Table 7: Compatible Command Centers ........................ 14
Table 8: Listings .................................................................... 16
Table 9: Battery Discharge/Recharge Schedule .........23
Table 10: Charging Status and Low Battery LEDs .....24
Table 11: Point Parameters ................................................33
Table 12: Data Expansion Loop Wire Specifications .38
Table 13: D8128D OctoPOPIT Switch Settings for
D8412G/D7412G .............................................44
Table 14: Terminal Strip Connections ............................. 47
Table 15: D8129 OctoRelay Switch Settings ..............49
Table 16: Number of D8128Ds Used with D8129s ..... 51
Table 17: Command Center Address Settings .............53
Table 18: Command Center Connections .....................53
Table 19: SDI Device Connections ................................. 57
Table 20: Printer Address Switch Settings.................... 57
Table 21: Access Control Module Address Switch
Settings .................................................................58
Table 22: ZONEX 1 Point Address Chart ..................... 71
Table 23: ZONEX 2 Point Address Chart ..................... 72