D9412GV2/D7412GV2
D9412GV2/D7412GV2 Release Notes for Version 7.09
F01U003637-06 Page 3 © 2013 Bosch Security Systems, Inc.
2.0 Firmware Revision History
2.1 Version 7.09
The following are corrections and changes made
since Version 7.08 in the GV2 Series Control
Panels.
• Changes were made to address the missing
low battery display from wireless devices on
the Zonex Bus
2.2 Version 7.08
The following are corrections and changes made
since Version 7.07 in the GV2 Series Control
Panels.
• Changes were made to address the issues
described in the GV2 Arming Without
passcode Technical Service Note (P/N:
F01U077005).
• Changes were made to the Passcode Arm
command to support the Easy Exit feature.
Entering a passcode followed by the [ENTER]
key on a keypad showing a Ready to Arm
state will cause all authorized areas within
scope to start or restart Exit Delay.
• Changes were made to the Perimeter Partial
arm command to no longer support the Easy
Exit feature. Now, the Perimeter Partial
command (COMMAND 8) must be initiated in
a disarmed area.
• Changes were made to the function list
arming commands to support the Easy Exit
feature. The arm level can be increased from
Perimeter Armed to Master Armed. The
function list Master Delay and Perimeter
Delay arming commands do not allow the Exit
Delay to be restarted when the area is
already at the same arm level.
• Corrections were made to ensure the Local
Only reporting feature was preserved for the
following intrusion alarm events: Recent
Close Alarm, Exit Error Alarm, Cross Zone
Alarm, and Unverified Alarm. This addresses
the issues described in the SIA Panic Alarms
Technical Service Note (P/N: F01U065901).
• Changes were made to the Status Report to
allow it to send through the enhanced
communication path to the central station
receiver. The status report is not intended to
print through a D9131A printer module.
• Corrections were made to the D1260 or
D1260B Keypad to allow it to Force Arm
when arming the last associated area when a
shared area is not Ready to Arm. It is
important to note that when arming the last
associated area, that the shared area must be
within the scope of the keypad.
• Improvements were made to allow invisible
points with
P# RlyResp Type set to 2 (Relay
Latches) to reset when the alarm memory is
cleared.
• Corrections were made the allow settings of
10 through 20 in the AC Fail Display prompt
to operate as expected.
• Corrections were made to the D720 keypad
to ensure the A, B and C keys now execute
their assigned custom functions.
• Corrections were made to the Walk Test
procedure to prevent faulted points with
P#
Point Index set to 0 from becoming Swinger
Shunt bypassed and producing erroneous
trouble events. This addresses the issues
described in Point Index 0 Technical Service
Note (P/N: F01U089352).
• Modifications were made to the Fire Walk
Test to differentiate between fire and
intrusion points left off-normal upon the
conclusion of the test. It is an ANSI SIA CP-01
requirement that any non-controlled points
left in an off-normal state upon the
conclusion of a Walk Test be prevented from
going into immediate alarm.
• Corrections were made to ensure the All
Points Tested event is generated at the
conclusion of a Walk Test procedure when
performed on a D1260 or D1260B keypad.
• Corrections were made to ensure the Walk
Test menu returns to idle text when left idle
for no more than 20 minutes. On GV2
firmware v7.07, when left idle the Walk Test
function remained active for approximately
60 min.
• Corrections were made to the D1260 or
D1260B keypad to ensure that user Index
Authority Level assignments made through
the Add/Change User function (COMMAND
56) are propagated to the D9210B door
controllers in a timely manner.
• Modifications were made to the D1260 or
D1260B keypads to never show the
All user-
authorized areas are now arming screen
To Next Page
Loading...
