To Next PageTo Next PageWhy is no steam coming out of my Bosch Sensixx x DA50 Iron?
If steam isn't coming out of your Bosch Iron, there could be several reasons. First, check that the steam control isn't set to the ' ' position. Second, make sure there is enough water in the tank; if not, fill it. The temperature may also be too low, or the anti-drip system may be activated.
Why does the spray not work on my Bosch Sensixx x DA50 Iron?
If the spray function on your Bosch Iron isn't working, there could be two reasons. First, check if there is water in the tank and fill it if necessary. Second, the mechanism might be obstructed.
What to do if water drips out of my Bosch Sensixx x DA50 Iron?
If water is dripping from the soleplate of your Bosch Iron along with steam, consider these factors: * The temperature control might be set too low; increase it if compatible with the fabric. * The steam control could be too high for the low temperature setting; reduce the steam control. * You may be pressing the shot of steam button too frequently; wait 5 seconds between each press. * You might be using pure distilled water or have added fragrant water to the tank; mix distilled water with tap water as directed and avoid adding other products unless recommended by Bosch.
How to clean Bosch Sensixx x DA50 Iron if deposits come out?
If deposits are coming out through the holes in the soleplate of your Bosch Iron, it indicates that traces of lime scale are coming out of the steam chamber. You should carry out a cleaning cycle referring to the “Calc’nClean” section.
How to fix Bosch Sensixx x DA50 when steam does not come out?
If steam isn't coming out of your Bosch Iron, first ensure that the steam regulator isn't set to the '0' position; adjust it to a higher setting. Also, check that the temperature isn't too low and increase it if the fabric is compatible. It is possible that the anti-drip system is activated.
Why my Bosch Iron does not heat up?
If your Bosch Iron isn't heating up, first check that the temperature control isn't set to the minimum; if it is, turn it to a higher setting. Also, if the 'auto off' indicator lamp is flashing, the 'secure' system may have been activated, putting the iron in stand-by mode. To reconnect it, gently move the iron around.
Why does no steam come out of my Bosch Sensixx x DA50?
If steam isn't coming out of your Bosch Iron, check these potential causes: * Ensure the steam control isn't set to the ' ' position; adjust it to an open steam position. * Verify that there's water in the tank; if not, fill it. * Make sure the temperature isn't too low; set it between '••' and 'max' and wait for the lamp to go out. * Note that the anti-drip system may be activated.
General| Type | Steam iron |
|---|---|
| Cordless | No |
| Cord length | 2.5 m |
| Swivel angle | 360 ° |
| Maximum power | 2400 W |
| Product color | Green, White |
| Soleplate type | Ceranium Glissée soleplate |
| Variable steam | Yes |
| Water tank capacity | 0.3 L |
| Steam boost performance | 180 g/min |
| Continuous steam performance | 40 g/min |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Non-twisting cord | - |
Weight and Dimensions| Depth | 122 mm |
|---|---|
| Width | 303 mm |
| Height | 151 mm |
| Weight | 1780 g |
| Package weight | 1960 g |
Instructions on how to fill the water tank with appropriate water types and levels.
How to iron using the appliance without steam.
How to iron using steam, including temperature and steam regulator settings.
Instructions on using the spray function.
How to use the shot of steam function for powerful steam bursts.
How to use the vertical steam function for steaming garments on hangers.
Automatic cleaning to remove scale deposits from the steam chamber.
Function to remove scale particles from the steam chamber.
Cartridge to reduce scale build-up and extend iron life.
Procedure for deep descaling using a special Bosch descaling liquid.
