Bosch Sensixx B25L User Manual (English)

Questions and Answers:

K
Kathleen StanleyAug 17, 2025
Why is my Bosch Sensixx B25L Iron not producing steam?
- H
  Henry RuizAug 17, 2025
  If your Bosch Iron is not producing any steam, several issues could be the cause. First, ensure the boiler is switched on and the water tank is not empty by setting the switch (4) to the “Start” position and filling the water tank if needed. Secondly, check that the water tank is correctly fitted onto the steam tank, listening for a click to confirm it's properly attached. Finally, verify that the steam regulator is not set to the minimum position; increase the steam flow by turning the steam control (5).
L
Lauren FerrellAug 19, 2025
Why is water coming out of the holes on my Bosch Iron?
- K
  Kathryn PriceAug 20, 2025
  If water is flowing through the holes on the sole plate of your Bosch Iron, it could be due to a couple of reasons. If you're using the steam function before the iron has reached the correct temperature, try reducing the steam flow when ironing at low temperatures by adjusting the variable steam control (5). Alternatively, if the water is condensing inside the pipes because steam is being used for the first time or hasn't been used in a while, point the iron away from the ironing area and press the steam release button (17) until steam is produced.
J
Jeffrey CortezAug 22, 2025
What to do if there is water leakage from the boiler of my Bosch Iron?
- W
  William YoungAug 22, 2025
  If you notice water leakage from the boiler of your Bosch Iron, it is likely because the drainage plug located at the bottom of the appliance is loose. Tighten up the boiler drainage plug with a coin.
W
Wayne WilsonAug 25, 2025
What to do if the Calc´n clean pilot lamp (9) on my Bosch Sensixx B25L Iron lights up continuously?
- R
  Roberto LopezAug 26, 2025
  If the Calc´n clean pilot lamp (9) lights up continuously on your Bosch Iron, it indicates that the boiler needs rinsing. Proceed to rinse the boiler according to the instructions, then switch the station off twice, keeping it off for at least 30 seconds each time.
D
David Allen DVMAug 27, 2025
Why does my Bosch Sensixx B25L Iron not stop steaming after placing it on the pad?
- N
  Natalie GoodmanAug 28, 2025
  If your Bosch Iron does not stop steaming after placing it on the pad, it is likely because the “Intelligent steam” function is activated. Simply press the trigger once again to stop the steaming immediately.
J
Joel Newton DDSAug 30, 2025
What to do if the garment sticks to the soleplate of my Bosch Sensixx B25L Iron?
- R
  Ryan RothAug 31, 2025
  If the ironed garment turns dark or sticks to the soleplate of your Bosch Iron, it indicates that the selected temperature is too high and has damaged the garment. To resolve this, select a suitable temperature for the material you are ironing and clean the sole plate with a damp cloth.
C
Cameron OlsonSep 2, 2025
Why is dirt coming out of my Bosch Sensixx B25L?
- L
  laura19Sep 2, 2025
  If dirt comes out through the sole plate of your Bosch Iron, it could be due to a build-up of scale or minerals in the steam tank. To resolve this, use tap water mixed 50% with distilled or demineralised water. It could also be caused by the use of chemical products or additives. In this case, clean the sole plate with a damp cloth, and never add any products to the boiler water.
K
kevinknightSep 4, 2025
Why am I experiencing loss of pressure during ironing with my Bosch Sensixx B25L Iron?
- E
  Evelyn HerreraSep 5, 2025
  If you experience a loss of pressure during ironing with your Bosch Iron, it's likely due to the steam release button being activated for an extended period. Use the steam release button (17) with intervals to improve the ironing result, allowing the textiles to dry and stay smooth better.
V
valvaradoSep 8, 2025
Why is the soleplate of my Bosch Iron turning brown?
- A
  antoniofreemanSep 8, 2025
  If the soleplate of your Bosch Iron turns brown, it is a regular consequence of usage. Clean the soleplate regularly with a damp cloth.
R
Ryan AndersonSep 12, 2025
Why does my Bosch Iron make a pumping sound?
- J
  Jerry CookSep 12, 2025
  If your Bosch Iron is making a pumping sound, it's likely because water is being pumped into the steam tank, which is normal. However, if the sound persists and does not stop, discontinue using the steam generator and contact an authorised technical service centre.

Bosch Sensixx B25L Specifications

General

Type	Steam Iron
Power	2400 W
Soleplate Material	Ceramic
Steam Output	40 g/min
Vertical Steam	Yes
Anti-Calc System	Yes
Drip-Stop System	Yes
Auto Shut-off	Yes
Self-cleaning	Yes