Why is my Bosch Sensixx'x DI90 Iron not heating up?
If your Bosch Iron isn't heating up, first ensure that the temperature control isn't set to the minimum; if it is, turn it to a higher setting. Also, check if the “SensorSteam” system has been activated, which puts the iron in stand-by mode. If so, grip the handle of the iron to restart it.
How to fix a Bosch Sensixx'x DI90 Iron that does not heat up?
If your Bosch Iron is not heating up, try the following: * Ensure the temperature control is not set to the minimum position; turn it to a higher setting. * Verify that the iron is receiving power by testing another appliance in the same socket or plugging the iron into a different socket. * If the “SensorSteam” system is activated, grip the handle of the iron to restart it.
What to do if water drips out of the soleplate of my Bosch Sensixx'x DI90?
If water is dripping from the soleplate of your Bosch Iron along with steam, it could be due to a temperature control setting that is too low. Try turning the temperature control to a higher setting and wait until the “TempOK” lights inside the temperature control stop flashing and remain lit. Also, avoid pressing the shot of steam button repeatedly without waiting 5 seconds between each press.
Why does steam not come out of my Bosch Iron horizontally?
If steam isn't coming out of your Bosch Iron when it's in a horizontal position, first check that the steam control isn't set to the “ ” position; if it is, set it to “eco” or “max”. Also, ensure the temperature isn't too low; if it is, set it to a higher temperature if the fabric allows.
What to do if deposits come out of my Bosch Iron?
If deposits are coming out through the holes in the soleplate of your Bosch Iron, it indicates traces of lime scale are exiting the steam chamber. You should carry out a cleaning cycle following the instructions in the “Calc’nClean” section.
Why is water dripping out of my Bosch Iron's soleplate?
If water drips out of the soleplate of your Bosch Iron along with steam, here are a few things to check: * Ensure the steam control isn't set to the " " position; adjust it to “eco” or “max”. * Make sure there's water in the tank; if not, fill it. * The temperature may be too low, activating the anti-drip system; increase the temperature setting to between “??” and “max” and wait for the “TempOK” lights to remain continuously lit. * Avoid repeatedly pressing the shot of steam button without waiting 5 seconds between presses. * If you're using pure distilled water or adding fragrant water, instead mix distilled water with tap water as directed and avoid adding other products unless recommended by Bosch.
Why are deposits coming out of the soleplate of my Bosch Iron?
If you see deposits coming out through the holes in the soleplate of your Bosch Iron, it indicates traces of lime scale are exiting the steam chamber. You should perform a cleaning cycle.
Why do clothes stick to my Bosch Sensixx'x DI90?
If clothes stick to your Bosch Iron, the temperature is likely too high. Turn the temperature control down and wait for the iron to cool.
What does it mean when the “SensorSteam” indicator lamp flashes on my Bosch Iron?
If the “SensorSteam” indicator lamp flashes on your Bosch Iron, it means the “SensorSteam” system has activated and the iron is in stand-by mode. To restart it, grip the handle of the iron.
Why are the lights inside the temperature control flashing on my Bosch Iron?
If the lights inside the temperature control of your Bosch Iron are flashing, it means the soleplate is either heating up or cooling down to the selected temperature. This is normal, and the lights will stop flashing once the selected temperature is reached.
Instructions on how to properly fill the water tank with tap water and warnings against using other liquids.
Explains the automatic steam generation based on handle grip, enhancing safety and energy saving.
Guides users on adjusting the soleplate temperature for different fabric types using the temperature control.
Instructions on setting steam control to 'eco' or 'max' and gripping the handle for continuous steam.
Describes how to cancel continuous steam and use the shot of steam button for targeted steam bursts.
Explains the self-clean filter's role in preventing scale and ensuring optimal steam production.
Details the Calc'nClean function to remove scale from the steam chamber, recommended for hard water areas.
Procedure for deep descaling using a special Bosch descaling liquid, recommended every three months.
Describes the anti-calc cartridge's function in reducing scale build-up and extending the iron's life.
General| Power | 2400 W |
|---|---|
| Steam Output | 50 g/min |
| Water Tank Capacity | 300 ml |
| Cord Length | 2.5 m |
| Vertical Steam | Yes |
| Anti-Scale System | Yes |
| Drip Stop System | Yes |
| Auto Shut-Off | Yes |
| Self-Cleaning Function | Yes |
| Anti-Drip System | Yes |
| Anti-Calc System | Yes |
| Type | Steam Iron |
| Soleplate | Ceramic |
To Next Page