Bosch Solution 880 - Default Chapter; Table of Contents

CC408 | Operators Guide | Contents EN | 3
Bosch Security Systems | 5/04 | 920050O.OG.112
Contents
1. Introduction ......................................................5
2. Specifications ....................................................5
3. Features .............................................................5
4. Codepad Indicators..........................................6
4.1 Zone Indicators.................................................6
4.2 AWAY Indicator..............................................6
4.3 STAY Indicator ................................................6
4.4 System Disarmed..............................................6
4.5 MAINS Indicator .............................................7
4.6 Off Indicator/Zone Sealed ..............................7
4.7 On Indicator/Zone In Alarm..........................7
4.8 FAULT Indicator .............................................7
4.9 Audible Indications..........................................7
5. Arming the System...........................................7
5.1 Arming in AWAY Mode.................................8
5.2 Arming in STAY Mode 1................................8
5.3 Arming in STAY Mode 2................................8
5.4 Programming STAY Mode 2 Zones ..............9
6. Disarming the System......................................9
7. User Codes........................................................9
7.1 Adding User Codes..........................................9
7.2 Adding Radio Remote User Codes................9
7.3 Deleting User Codes/Radio User Codes.......9
8. Radio Transmitter Operations......................10
9. Alarms .............................................................10
9.1 Duress Alarm..................................................10
9.2 Panic Alarm ....................................................10
9.3 Fire Alarm.......................................................11
9.4 Medical Alarm................................................11
9.5 Tamper Alarm (Access Denied) ...................11
10. Isolating Zones................................................11
10.1 Standard Isolating ..........................................11
10.2 Code to Isolate ...............................................11
11. Setting the Date and Time ............................11
12. Fault Analysis Mode ......................................12
12.1 AC Fail ............................................................12
12.2 System Faults ..................................................12
12.3 Fault Descriptions...........................................12
13. Telco Arm/Disarm Sequence (Call Forward
On/Off) ...........................................................13
13.1 Telco Arm Sequence......................................13
13.2 Telco Disarm Sequence.................................13
14. Turning Outputs On/Off...............................14
15. Reset Latching Outputs................................. 14
16. Codepad ID/Buzzer Tone Change ..............14
17. Testing............................................................. 14
17.1 Horn Speaker Test......................................... 14
17.2 Bell Test .......................................................... 14
17.3 Strobe Test...................................................... 14
17.4 Walk Test Mode............................................. 14
17.5 Test Report .....................................................14
18. Event Memory Recall.................................... 15
19. Day Alarm ...................................................... 15
20. Remote Arming By Telephone .................... 15
21. Domestic Dialling .......................................... 16
21.1 Acknowledging Domestic Calls.................... 16
21.2 Programming Domestic Telephone
Numbers.......................................................... 16
21.3 Disable Domestic Dialling ............................ 16
22. Partitioning ..................................................... 17
22.1 Master Partitioned Codepad Indicators....... 17
22.1.1 Zone Indicators .............................................. 17
22.1.2 Area On/Off Indicators.................................17
22.2.1 Area Display Indicators................................. 17
22.2.2 Status Indicators .............................................17
22.3 Operating From A Master Partitioned
Codepad.......................................................... 17
22.4 Operating From Area Addressable
Codepads ........................................................ 17
23. Basic Pager Reporting ................................... 18
24. Glossary of Terms..........................................20
25. Installation Notes ........................................... 22
Figures
Figure 1: CP5 Eight Zone LED Codepad............... 6
Figure 2: CP5 Eight Zone LCD Codepad .............. 6
Figure 3: RE012 – 2 Channel Keyfob
Transmitter .............................................. 10
Figure 4: RE013 – 4 Channel Keyfob
Transmitter .............................................. 10
Figure 5: CP5 LED Codepad Showing Audible
Alarm Buttons ......................................... 10
Figure 6: Master Partitioned Codepad.................. 17
Figure 7: Basic Pager Display ................................ 19