Bostitch LHF97125 User Manual

BT125, BT200, SL150, SX150, LHF97125,
SX150-BHF, S97125, USO56 & SL125OC
PNEUMATIC BRAD NAILERS & STAPLERS
ENGRAPADORAS NEUMATICAS
CLOUEURS ET AGRAFEURS PNEUMATIQUES
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACION Y DE MANTENIMIENTO
MANUEL D'INSTRUCTIONS ET D'ENTRETIEN
[AAOVeRTE.C,A:] ATTe.T,O.,]
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERAN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUlR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNiQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUlDOR.
LIRE ATTENTIVEMENT LE PRI_SENT MANUEL AVANT D'UTILISER L'APPAREIL. PRINTER UNE
ATTENTION TOUTE PARTICULI#RE AUX CONSIGNES DE SleCURIT# ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L'OUTIL POUR FUTUR R#F#RENCE. SI
VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRleSENTANT OU VOTRE
CONCESSIONNAIRE BOSTITCH.
STANLEY FASTENING SYSTEMS L.P.
121037REVJ 6/07

Bostitch LHF97125 Specifications

General

Brand	Bostitch
Model	LHF97125
Category	Nail Gun
Language	English

Summary

Safety Instructions and Warnings

Eye Protection Requirements

Mandatory eye protection conforming to ANSI Z87.1 for frontal and side protection.

Power Source and Air Supply Safety

Prohibits oxygen, combustible gases, and excessive pressure (over 200 PSIG) for safety.

Loading Tool Safety Precautions

Emphasizes avoiding accidental discharge during loading: no hands in discharge area, no pointing.

General Safe Operation Practices

Instructs to handle tools with care, never engage in horseplay, and only pull trigger towards work.

Contact Arm and Trigger Control Safety

Advises against holding trigger pulled on contact arm tools except during fastening.

Recoil and Bounce Hazard Awareness

Keep hands and body away from discharge area due to recoil bounce risk.

Fastener Driving Angle and Placement

Fire and Explosion Hazard Warning

Highlights fire/explosion risk from sparks near flammable materials; prohibits use.

Tool Specifications and Air Requirements

Operating Pressure Guidelines

Recommends operating pressure range for optimal fastener performance.

Pneumatic Tool Operation Modes

Contact Trip Operation

Tool drives fastener when contact trip touches work and trigger is pulled. Risk of double fire.

Sequential Trip Operation

Trigger Operation Mode

Detailed Air Supply and Connections

Power Source Restrictions

Reiterates prohibition of oxygen, combustible gases, and pressure exceeding 200 PSIG.

Regulator and Operating Pressure

Loading Tool Instructions and Safety

Safety During Loading Procedures

Reinforces eye protection and lists critical safety points to prevent accidental injuries during loading.

Loading Procedure for Specific Models

Dial-A-Depth™ Fastener Control

Depth Adjustment Feature

Additional Safe Operation Warnings

Tool Operation Procedures

Before Handling or Operating Tool

Contact Trip Operation Methods

Sequential Trip Operation Method

Trigger Operation Method

Tool Operation Checks and Maintenance

Tool Operation Check Procedures

Maintaining the Pneumatic Tool

Trouble Shooting Guide

Common Tool Problems and Solutions

Lists common issues like air leaks, failure to cycle, lack of power, and skipping fasteners with causes and corrections.