Bostitch BTFP72155 User Manual

9R205731RC 07/15
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER
UNE ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS
AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE
BOSTITCH.
BTFP72155 / BTFP72156
SMART POINT
TM
15 GA ANGLED FINISH NAILER
CLAVADORA NEUMÁTICA ANGULAR PARA CALIBRE
15 SMART POINT™
CLOUEUSE DE FINITION À ANGLE DE
CALIBRE 15 SMART POINT
MC

Bostitch BTFP72155 Specifications

General

Brand	Bostitch
Model	BTFP72155
Category	Nail Gun
Language	English

Summary

LIMITED WARRANTY

SAFETY INSTRUCTIONS

Eye Protection Requirements

Details required eye protection conforming to ANSI specifications.

Mandatory Air Supply Disconnection

Lists critical times to disconnect air supply for safety.

AIR SUPPLY AND CONNECTIONS

Prohibited Gas Power Sources

Prohibits use of oxygen, combustible, or bottled gases due to explosion risk.

OPERATION

Selectable Trigger Mode Explained

Describes the selectable trigger mode: sequential vs. contact.

General Tool Handling Safety

Lists essential safety rules for handling the pneumatic tool.

Flammable Material Warning

Warns about sparks and use near flammable materials to prevent explosions.

MAINTAINING THE TOOL

TOOL COMPONENTS

TOOL SPECIFICATIONS

FASTENER SPECIFICATIONS

AIR SUPPLY AND CONNECTIONS

Recommended Air Supply Source

Mandates using only clean regulated compressed air for operation.

Air Filter Importance

Explains the importance of an air filter for maintaining tool performance.

LOADING THE TOOL

Preventing Accidental Injuries

Lists critical safety measures to prevent accidental injuries during loading.

LOADING THE BTFP72155/BTFP72156

Load and Pull Pusher Method

Step-by-step guide for loading nails using the pull pusher method.

TRIP OPERATION MODE

Contact Trip Operation Explained

Explains the 'Contact Trip' mode and its fastener driving operation.

Sequential Trip Operation Explained

Explains the 'Sequential Trip' mode and its fastener driving operation.

SELECTING THE TRIP MODE

DIAL-A-DEPTH® FASTENER CONTROL ADJUSTMENT

GENERAL SAFE OPERATION GUIDELINES

Misuse and Handling Risks

Highlights the risks of misuse and improper handling of the tool.

Trigger/Trip Actuation Lockout

Prohibits disabling the trigger or contact trip mechanisms for safety.

BELT HOOK FUNCTIONALITY

INTEGRATED AIR BLOWER OPERATION

Air Blower Safety Warning

Warns against blowing debris towards oneself or others when using the air blower.

TOOL OPERATION

Contact Trip Operation Methods

Details operation for Contact Trip mode: single and rapid fastener placement.

Sequential Trip Operation Method

Details operation for Sequential Trip mode, emphasizing workpiece contact.

JAM CLEARING PROCEDURE

Nail Jam Clearing Steps

Step-by-step guide for clearing jammed nails from the tool's open drive channel.

TOOL OPERATION CHECK PROCEDURE

Post-Damage Operation Check

Reiterates performing an operation check if the tool is dropped or suspected damaged.

MAINTAINING THE PNEUMATIC TOOL

Genuine Replacement Parts

Recommends using only genuine BOSTITCH replacement parts for maintenance.

Air Supply Pressure and Volume Importance

Explains the importance of adequate air volume and potential flow restrictions.

AVAILABLE ACCESSORIES