Bostitch SX1838 User Manual

BT1855 & SX1838
PNEUMATIC BRAD NAILER & STAPLER
CLAVADORA Y ENGRAPADORA NEUMÁTICA
CLOUEUSE À TÊTE PERDUE ET AGRAFEUSE
180585RC 11/13
BOSTITCH FASTENING SYSTEMS
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS
AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE
BOSTITCH.
?180585RC_BT1855-SX1838_Tools_Man_AC:121037RevH_BTSLSX_Manual.qxd 2013/11/12 ? 午12:05 Page 1

Bostitch SX1838 Specifications

General

Model	SX1838
Gauge	18
Operating Pressure	70-120 PSI
Power Source	Pneumatic
Air Inlet	1/4" NPT
Magazine Capacity	100

Summary

INTRODUCTION

LIMITED WARRANTY - U.S. and Canada Only

SAFETY INSTRUCTIONS

TOOL COMPONENTS

TOOL SPECIFICATIONS

FASTENER SPECIFICATIONS

Lists compatible fastener types, gauges, and lengths for each tool model.

AIR SUPPLY AND CONNECTIONS

REGULATOR

Specifies the need for a pressure regulator for safe operation.

OPERATING PRESSURE

Explains the recommended operating pressure range and its importance.

LOADING THE BT1855 & SX1838

LOADING THE SX1838

Procedure to load staples into the SX1838 model.

LOADING THE BT1855

Procedure to load brads into the BT1855 model.

TRIGGER LOCKOUT CONTROL

TRIP OPERATION MODES

Contact Trip Operation

How to use the tool with the contact trip mechanism for rapid fastening.

Sequential Trip Operation

How to use the tool with the sequential trip mechanism for precise placement.

DIAL-A-DEPTH FASTENER CONTROL ADJUSTMENT

ADDITIONAL SAFE OPERATION WARNINGS

Lists crucial safety rules and precautions to observe during operation.

INSTALLING THE BELT HOOK

USING THE INTEGRATED PENCIL SHARPENER

HEX WRENCH STORAGE

TOOL OPERATION

CONTACT TRIP OPERATION

Step-by-step guide for using the contact trip mode.

SEQUENTIAL TRIP OPERATION

Step-by-step guide for using the sequential trip mode.

JAM CLEARING PROCEDURE

BT1855 JAM CLEARING

Specific steps to clear jams for the BT1855 model.

SX1838 JAM CLEARING

Specific steps to clear jams for the SX1838 model.

TOOL OPERATION CHECK

MAINTAINING THE PNEUMATIC TOOL

REPLACEMENT PARTS

Guidance on using genuine BOSTITCH replacement parts.

ASSEMBLY PROCEDURE FOR SEALS

Instructions for lubricating and assembling seals during maintenance.

AIR SUPPLY-PRESSURE AND VOLUME

Importance of air supply parameters for tool performance.

MAINTENANCE CHECKLIST

TROUBLESHOOTING

AVAILABLE ACCESSORIES

BOSTITCH FINISH & TRIM PRODUCTS