Braeburn 7320 Installer's Guide

Installer Guide 12
15 AC Power Interrupt Warning [note 6]–Whenenabled,thethermostatwilldisplayanoutagewarning
 whenACpowertothethermostatislost.
16 Short Cycle Protection–Selectsthenumberofminutesthecoolingcompressorwillbelockedoutafter
 turningoff.Thisshortcycleprotectionisalsoactiveintheheatmodeifaheatpumpsystemwasselectedin
 Option6.
17 Residual Cooling Fan Delay–Selectsadelayforthesystemfanafterthecoolingcompressorhasturned
 off.Thisdelaywillhelpremovetheremainingcoolairoutoftheductworkprovidingadditionalefciency.
18 Circulating Fan Lock–Whenenabled,theonlyuserfanoptionsavailableareONandCIRC(Circulation).
 TheAUTOoptionisnotavailablewiththisoptionenabled.
19 Adaptive Recovery Mode (early recovery) [note 7]–EnablesordisablestheARM
TM
(adaptiverecovery
 mode)feature.DuringARM,roomtemperatureisrecoveredbyturningontheheatingorcoolingbeforethe
 endofthesetbackperiod.Thesetpointtemperatureischangedtothatoftheupcomingprogramtemperature.
20 Indoor Remote Sensor Control [note 8]–IfaBraeburn
®
indoorremotesensorisconnected(wired)or
 paired(wireless)duringinstallation,thethermostatwillautomaticallydetectthesensor.Whenanindoor
 sensorisdetected,youmayselectbetweenthermostatonly(ISENS),remotesensoronly(ESENS)or
 combiningthethermostatandtheremotesensor(s)(ASENS).
NOTE: This option does not apply to the Braeburn outdoor sensor. When an outdoor sensor is connected
(wired) or paired (wireless), the thermostat automatically recognizes it and no further configuration
is necessary.
21 Lockout Security Level–Selectsthelevelofkeypadlockoutwhenthethermostatislocked.Level2locks
theentirethermostat(includingthefrontresetbutton).Level1lockseverythingexcepttheSpeedBar
®
 allowingforupanddowntemperatureadjustment.NOTE: The lock code is set in the User Settings mode
(see User Manual).
22 Auto Changeover Dead Band [note 9]–Whenautochangeovermodeisenabledinoption5and
 selected,thesystemautomaticallyswitchesbetweenheatingandcoolingwhentheroomtemperature
 meetsthenormalcriteriaforeitheraheatingorcoolingcall.Thereisaforcedseparation(deadband)
 betweentheheatingandcoolingsetpointssothatthesystemsdonotworkagainsteachother.This
 optionselectstheamountofthisdeadbandindegreeswiththedefaultbeing3°F.
23 Compressor Balance Point [notes 4, 10]–Locksouttheuseofthecompressorheatstagewhenthe
 outsideairtemperatureislessthantheselectedsettingof0˚Fto50°F(-9°Cto10°C)
24 Auxiliary Heat Balance Point [notes 4, 10]–Locksouttheuseoftheauxiliaryheatstagewhenthe
 outsideairtemperatureexceedstheselectedsettingof70°Fto40°F(21°Cto4°C).NOTE: This balance
point overrides the fossil fuel compressor lockout in option 13. If this option is set to gas and the outdoor
temperature is over the auxiliary balance point, the compressor will remain on during a call for auxiliary heat.

Braeburn 7320 Specifications

General

Brand	Braeburn
Model	7320
Category	Thermostat
Language	English