Braeburn Premier 5000 - User Manual

MODEL
5000
USER MANUAL
Premier Series
5-2 Day Programmable
Single Stage Heat/Cool
Digital Thermostat
Compatible with low voltage single stage gas,
oil or electric heating or cooling systems,
including single stage heat pumps. This
thermostat can also be used on 250mv to
750mv millivolt heating only systems. Do not
use this thermostat on applications with
voltages above 30 Volts AC.
READ ALL INSTRUCTIONS BEFORE PROCEEDING
© 2005 Braeburn Systems LLC • Patents Pending • All Rights Reserved. Pub. No. 5000-100-005
WARNING!
Important Safety Information
• Always turn off power to the air conditioning or heating system prior to installing,
removing, cleaning or servicing thermostat.
• Read this manual thoroughly prior to installing, programming or operating
this thermostat.
• This thermostat is designed for use with a 24 Volt-AC low voltage single stage
gas, oil or electric heating or cooling systems, including single stage heat
pumps. This thermostat can also be used on 250mv to 750mv millivolt heating
only systems.
• Do not use this thermostat on applications with voltages above 30 Volts AC.
• This thermostat requires two (2) properly installed "AA" alkaline batteries to
provide power for the thermostat to properly control the system operation.
• Wiring must conform to all building codes and ordinances as required by local
and national code authorities having jurisdiction.
• Do not short (or jumper) across terminals on the gas valve or at the heating or
cooling system control board to test the thermostat installation. This could
damage the thermostat and void the warranty.
• Do not select COOL mode of operation if the outside temperature is below
50˚ F (10˚ C). This could damage the controlled cooling system and cause
personal injury.
• This thermostat should only be used as described in this manual. Any other use
is not recommended and will void the warranty.
SPECIFICATIONS
1
1
• Electrical Rating: 24 Volt AC (18-30 Volt AC)
1 amp maximum load per terminal
2 amp total maximum load (all terminals)
• Control Range: 45˚ - 90˚ F (7˚ - 32˚ C)
• Accuracy: +/- 1˚ F (+/- .5˚ C)
• DC Power: 3.0 Volt DC (2 AA Alkaline batteries included)
• Compatibility: Compatible with low voltage single stage gas, oil or electric
heating or cooling systems, including single stage heat pumps. This thermostat
can also be used on 250mv to 750mv millivolt heating only systems.
• Terminations: Rc, Rh, G, W, Y, B, O
INSTALLATION
2
2.1
Replacing Existing Thermostat
1. Always turn off power to the air conditioning or heating system prior to removing
existing thermostat.
2. Remove the cover of your old thermostat and locate the wire terminals. Do not remove
wires from terminals yet.
3. Using small pieces of masking tape, label wires prior to removal from terminals. Use
the chart below to determine the new terminal designations for your new thermostat.
Old Terminal from New Terminal for
Existing Thermostat New Thermostat Terminal Description
V or Rc Rc Cooling Transformer
M, 4, Rh, or R Rh Heating Transformer
G or F G Fan Control
H, W or 4 W Heating Control
Y Y Cooling Control
B B Reversing Valve (Heating)
O O Reversing Valve (Cooling)
C None-Cap the wire 24 Volt AC, Transformer Common
CONTENTS
SPECIFICATIONS
INSTALLATION
TESTING YOUR NEW THERMOSTAT
PROGRAMMING
ADDITIONAL OPERATION FEATURES
TROUBLESHOOTING
WIRING DIAGRAMS
1
2
3
4
5
6
7

Summary

1 SPECIFICATIONS

2 INSTALLATION

2.1 Replacing Existing Thermostat

Instructions for removing an old thermostat and labeling wires.

2.2 Installing Your New Thermostat

Step-by-step guide for mounting and wiring the new thermostat sub-base.

3 TESTING YOUR NEW THERMOSTAT

4 PROGRAMMING

4.1 Default Thermostat Settings

Details the factory default settings for various thermostat functions.

4.2 Setting Current Time of Day and Day of Week

Guides users on setting the correct time and day for accurate operation.

4.3 Setting Thermostat User Options

Explains how to customize user-configurable settings for optimal performance.

4.4 Setting Your Energy Saving Programs-Tips Before Starting

Advice on setting up energy-saving programs and default schedules.

5 ADDITIONAL OPERATION FEATURES

5.1 Review Set Temperature

How to view the current set temperature and override it.

5.2 Temporary Program Override

Manually adjust setpoint temporarily, resetting automatically.

5.3 Extended Hold (Vacation) Mode

Locks the current setpoint indefinitely or for 24 hours.

5.4 Filter Check Monitor

Displays reminders for filter replacement or cleaning.

5.5 Locking the Keypad

Prevents accidental changes by locking the keypad.

5.6 Adaptive Recovery Mode (ARMTM)

Optimizes comfort and energy by adjusting recovery timing.

5.7 Recirculating Fan Mode

Circulates air for better temperature distribution and air quality.

5.8 High Temperature Safety Switch

Thermostat automatically turns off above a certain temperature.

5.9 Low Temperature Freeze Protection

Initiates heat call if room temperature drops very low.

5.10 Compressor Protection

Protects the compressor from short cycling by adding a delay.

5.11 Low Battery Detection and Replacement

Explains low battery indicator and how to replace batteries.

5.12 Resetting the Thermostat

How to reset the thermostat to factory defaults.

6 TROUBLESHOOTING

7 WIRING DIAGRAMS

Braeburn Premier 5000 Specifications

General

Wi-Fi Connectivity	Yes
Power Source	24V AC
Filter Change Alert	Yes
Keypad Lock	Yes
Backup Battery	No
Compatibility	Heating and cooling systems
Display	Touchscreen
Mobile App	Braeburn app
Programmable	Yes
Programmability	Multiple schedules, up to 4 time periods per day
Operating Temperature Range	32°F to 104°F (0°C to 40°C)
Operating Humidity Range	0% to 90% RH
Terminals	R, C, W, Y, G, O/B
Hold Feature	Yes