Braun ThermoScan 6 - User Manual

Questions and Answers:

K
Kelly HunterAug 18, 2025
What to do if the Braun ThermoScan 6 displays 'System error – self-check display'?
- A
  acareyAug 19, 2025
  If your Braun thermometer shows a 'System error – self-check display', try the following steps: First, wait one minute until the thermometer flashes continuously and does not turn off automatically, then turn it on again. If that doesn't work, reset the thermometer by removing the batteries and putting them back in. As another option, replace the batteries with new ones. If the issue persists, please contact the Service Center.
B
benjamincruzAug 20, 2025
What to do if my Braun Thermometer says 'POS' or position error?
- T
  Tara BrownAug 21, 2025
  If your Braun thermometer displays 'POS,' which indicates a position error, press the Start button to begin a new measurement.
W
wattsjeffreyAug 23, 2025
What to do if Braun ThermoScan 6 Thermometer says an accurate measurement was not possible?
- B
  barnettalbertAug 25, 2025
  If your Braun Thermometer indicates that an accurate measurement wasn't possible, replace the hygienic lens filter, reposition the thermometer, and press the Start button to begin a new measurement.
R
randallruizAug 26, 2025
What to do if Braun ThermoScan 6 Thermometer shows temperature is not within range?
- T
  Tammy SmithAug 26, 2025
  If the temperature reading on your Braun Thermometer is not within the typical human temperature range (93.2 – 108 °F or 34 – 42.2 °C), ensure the probe tip and lens are clean, and that a new, clean hygienic lens filter is attached. Also, make sure the thermometer is properly inserted. Then, take a new temperature.
L
lsmithAug 28, 2025
What to do if Braun ThermoScan 6 Thermometer battery is low?
- J
  johnparkerAug 28, 2025
  If your Braun Thermometer indicates that the battery is low, insert new batteries.
A
Alexander DuffyAug 30, 2025
Why is my Braun Thermometer showing a temperature outside the normal range?
- A
  Andrew LarsonAug 30, 2025
  If your Braun thermometer displays a temperature that is not within the typical human range (93.2 – 108 °F or 34 – 42.2 °C), ensure that the probe tip and lens are clean and that a new, clean lens filter is attached. Also, make sure the thermometer is properly inserted before taking a new temperature.
R
Richard BellSep 1, 2025
What to do if my Braun ThermoScan 6 Thermometer shows the battery is too low?
- E
  ericmaySep 1, 2025
  If the battery of your Braun thermometer is too low to take a correct temperature measurement, insert new batteries.
C
Christine AlexanderSep 4, 2025
What to do if my Braun ThermoScan 6 says 'An accurate measurement was not possible'?
- L
  Laura RodriguezSep 4, 2025
  If your Braun thermometer indicates that an accurate measurement was not possible, replace the lens filter and reposition the thermometer.
T
Tammy SchaeferSep 6, 2025
Why Braun Thermometer says battery is too low?
- T
  terrywalkerSep 6, 2025
  If your Braun Thermometer indicates that the battery is too low to take an accurate temperature measurement, replace the batteries with new ones.
C
Carlos LoveSep 8, 2025
Why Braun ThermoScan 6 ambient temperature is not with the allowed operating range?
- W
  Wayne NewmanSep 8, 2025
  If your Braun Thermometer displays that the ambient temperature is not within the allowed operating range (50 – 104 °F or 10 – 40 °C), allow the thermometer to remain for 30 minutes in a room where the temperature is between 50 and 104 °F or 10 and 40 °C.

Braun ThermoScan 6 Specifications

General

Measurement Method	Infrared
Display	LCD
Battery Type	2 AA batteries
Type	Ear thermometer
Age Precision Technology	Yes
Fever Indicator	Yes, color-coded display
Memory Readings	1
Measurement Site	Ear
Display Resolution	0.1°C or 0.1°F
Fever Guidance	Yes
Probe Covers	Disposable lens filters
Accuracy	±0.2°C (±0.4°F)
Age Recommendation	All ages
Special Features	Pre-warmed tip
Measurement Time	A few seconds
Memory	Last reading