EasyManua.ls Logo

Bray 5A Series - User Manual

Bray 5A Series
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SERIES 5A AND 5B
INTRINSICALLY SAFE VALVE STATUS MONITOR
Installation, Operation and Maintenance Manual
THE HIGH PERFORMANCE COMPANYBRAY.COM

Table of Contents

Questions and Answers

  • T
    Travis DeanAug 16, 2025
    What to do if Bray 5A signal is not received?
    • J
      Jeremy GarciaAug 16, 2025
      If you are not receiving a signal from your Bray Measuring Instruments, there are several potential causes: * The wiring inside the VSM might not be connected. Rewire the field wiring and verify the torque applied to the terminal block. * The cams may be set outside of the actuator range. Adjust the cam position. * The switches may be damaged. Check the power ratings of the switches against the application requirements.
  • M
    Michelle PetersonAug 19, 2025
    Why visual indication of Bray 5A Measuring Instruments is opposite of actuator position?
    • C
      christophermeyersAug 19, 2025
      If the visual indication on your Bray Measuring Instruments is opposite of the actuator position, it could be because the visual indication was reversed, or the VSM was mounted at a 90-degree angle. To correct this, reverse the visual indication or remount the VSM.
  • K
    Kelly MendozaAug 22, 2025
    What to do if Bray Measuring Instruments VSM does not rotate?
    • J
      Jeremy MckinneyAug 22, 2025
      If the VSM on your Bray Measuring Instruments is not rotating, the issue might stem from: * Improper mating between the bracket or adapter and the actuator. Check the bracket and adapter to ensure they fit correctly, and adjust as needed. * The actuator itself not moving as commanded. Consult the troubleshooting chart in the actuator IOM and check the field wiring.
  • D
    Daniel WhiteAug 26, 2025
    What to do if Bray 5A Measuring Instruments has corrosion inside?
    • E
      edward88Aug 26, 2025
      If you find corrosion inside your Bray Measuring Instruments, it may be due to: * Condensation forming. Seal the conduit opening to prevent this. * Water ingress. Inspect all seals and check for potential water entry points through the conduit.
  • D
    David EllisonAug 28, 2025
    What to do if Bray Measuring Instruments receives open signal in close position?
    • Z
      zreyesAug 28, 2025
      If your Bray Measuring Instruments receive an open signal when in the close position (or vice versa), the field wiring may be reversed. Rewire the field wiring to resolve this issue.
  • P
    Pamela WhitneyAug 31, 2025
    What to do if the Bray Monitor signal is not received?
    • J
      Joshua CombsAug 31, 2025
      If the signal is not being received by your Bray Monitor, there are several potential causes. First, the wiring inside the VSM might not be properly connected; rewire the field wiring and check the applied torque to the terminal block. Another cause could be that the cams are set outside of the actuator range; in this case, you should adjust the cam position. Finally, there might be damage to the switches; check the power ratings of the switches versus the application.
  • M
    mackenziecarrilloSep 3, 2025
    Why is there corrosion inside my Bray Monitor unit?
    • M
      Mr. Francisco AcostaSep 3, 2025
      Corrosion inside your Bray Monitor unit can occur due to a couple of reasons. One reason is condensation forming within the unit; to resolve this, seal the conduit opening. Another reason is water leaking into the unit; inspect all seals and check for any potential water entry points through the conduit.
  • T
    thomasdennisSep 6, 2025
    What to do if the Bray Monitor VSM does not rotate?
    • J
      jjonesSep 6, 2025
      If the VSM on your Bray Monitor isn't rotating, it could be due to a couple of reasons. First, the bracket or adapter might not be mating properly with the actuator; check the bracket and adapter for a proper fit and adjust as needed. Another possibility is that the actuator itself isn't moving as commanded; in this case, check the troubleshooting chart in the actuator IOM and also check the field wiring.
  • F
    fmorenoSep 9, 2025
    What to do if the visual indication is opposite of the actuator position on my Bray Monitor?
    • J
      johncollinsSep 9, 2025
      If the visual indication on your Bray Monitor is showing the opposite of the actuator's actual position, it's likely that the visual indication was reversed, or the VSM was mounted at a 90-degree angle. To correct this, reverse the visual indication or remount the VSM.
  • B
    Brandy HerreraSep 12, 2025
    What to do if an open signal is received in the close position (or vice versa) on my Bray Monitor?
    • J
      Jennifer WatkinsSep 12, 2025
      If your Bray Monitor is receiving an open signal when it should be closed (or vice versa), the field wiring is likely reversed. Rewire the field wiring to correct this issue.

Bray 5A Series Specifications

General IconGeneral
BrandBray
Model5A Series
CategoryMeasuring Instruments
LanguageEnglish