Briggs & Stratton 15kW

Questions and Answers

E
Emily GriffinAug 19, 2025
What to do if my Briggs & Stratton Generator engine won't start or runs rough?
- A
  Alison JonesAug 19, 2025
  If your Briggs & Stratton Generator engine will not start, or starts and runs roughly, there are several potential causes. First, check the 15 Amp fuse and replace it if it's missing or blown. The electronic governor might not be working properly, requiring you to contact a local service facility. Ensure that the fuel supply is turned on and not depleted, checking the propane tank if applicable. Verify that the fuel selector switch is set correctly. A failed battery could also be the issue, so try replacing it. Lastly, a clogged air filter can cause starting problems, so clean or replace the air filter.
L
Lindsey SmithAug 21, 2025
Why does my Briggs & Stratton Generator engine shut down during operation?
- M
  Matthew MeltonAug 21, 2025
  If your Briggs & Stratton Generator engine shuts down during operation, it could be due to a couple of reasons. First, make sure that the fuel supply hasn't been turned off or depleted; check the fuel valves and fill the propane tank if necessary. Also, check the control board digital display for a service code.
I
Ian Riley IIAug 23, 2025
What causes a Briggs & Stratton Generator to not stop when utility power returns?
- O
  oliverclaytonAug 25, 2025
  If your Briggs & Stratton Generator continues to run after utility power returns, it could be due to several reasons. There may be blown fuses in the transfer switch, so try installing new fuses. It's also possible that the 5-minute minimum runtime hasn't elapsed yet, so wait 5 minutes. Poor wire connections or defective controllers could also be the cause; check and repair the connections, or contact a local service facility.
S
Steven KennedyAug 26, 2025
Why Briggs & Stratton Portable Generator will not start?
- H
  Heidi MartinAug 26, 2025
  If your Briggs & Stratton Portable Generator won't start or runs roughly, there are a few things to check. Begin by inspecting the 15 Amp fuse; install a new one if it's missing or blown. Then, make sure the fuel supply is on and not depleted by opening the fuel valve(s) and checking the propane tank. Finally, examine the battery and replace it if it has failed.
J
Juan FullerAug 28, 2025
Why does my Briggs & Stratton Generator engine bog down under load?
- C
  Courtney RussellAug 28, 2025
  If your Briggs & Stratton Generator engine runs well without any load but falters when loads are connected, it could be due to several reasons. First, the generator might be overloaded, so try removing some loads. There could also be a short circuit in a connected load, in which case you should disconnect the shorted electrical load. Other potential causes include a shorted generator circuit, incorrect fuel pressure or mixture (refer to the Gaseous Fuel System section in the installation manual), a kinked fuel line between the regulator and the engine (remove the kink or replace the line if necessary), or a malfunctioning Electronic Governor system, which may require contacting a local service facility.
J
James HarrisAug 30, 2025
How to troubleshoot a Briggs & Stratton Generator with no AC output?
- R
  Robert VegaAug 30, 2025
  If your Briggs & Stratton Generator is running, but there's no AC output, it could be due to a few reasons. The circuit breaker might be open or defective, so try resetting or replacing it. There might be a service code in the generator control board, which requires contacting a local service facility. Poor wiring connections or a defective transfer switch could also be the cause; check and repair the wiring, or contact a local service facility.
A
Alexis ClementsSep 1, 2025
What to do if there is a loss of power on circuits with my Briggs & Stratton Generator?
- S
  Sharon WhiteSep 1, 2025
  If you experience a loss of power on circuits with your Briggs & Stratton Generator, the generator circuit breaker might be open. Try resetting it. Also, there may be problems with the transfer switch.
K
Kathleen SullivanSep 3, 2025
Why won't my Briggs & Stratton Generator unit exercise?
- S
  stokeslindaSep 3, 2025
  If your Briggs & Stratton Generator unit will not exercise, first ensure the control board is set to AUTO by pressing the AUTO button. Then, check that the exercise timer is properly set and not turned OFF. Verify the unit date and time are correctly set. A failed battery could also be the cause, so replace the battery. Lastly, check the 15 Amp fuse and install a new one if it is missing or blown.
M
Mary WrightSep 5, 2025
Why do I smell fuel coming from my Briggs & Stratton Generator?
- S
  Samantha ObrienSep 5, 2025
  If you notice an odor of fuel from your Briggs & Stratton Generator, it's likely due to a fuel leak. Turn off the manual shutoff fuel valve and contact a local service facility.
A
Angela GuzmanSep 7, 2025
How to fix excessive vibration in my Briggs & Stratton Generator?
- H
  hcombsSep 7, 2025
  If your Briggs & Stratton Generator is experiencing excessive vibration, it may be due to a loose mechanical fastener. Check and repair any loose fasteners, or contact a local service facility.