Brightz CoolerBrightz

To Next Page

Page 1 of 2

CoolerBrightz

™

Instruction

Patent Pending

IMPORTANT BATTERY INFORMATION:

CoolerBrightz™ includes 2x CR2050 (3V) batteries.

Step 1 – Operation

To operate CoolerBrightz

, Press top center of CoolerBrightz

to turn on and

start color changing. Press top center again to stop on desired color. To turn off

CoolerBrightz

press top center again after color stop.

* CoolerBrightz

will automatically turn off after 3 hours to conserve battery.

Step 2 – Installation

CoolerBrightz™ is water resistant and looks best when placed within, or underneath

ice, providing an awesome glow.

The easiest method:

1. Add a layer of ice to fill the bottom half of the cooler.

2. Position CoolerBrightz

on top of the ice. CoolerBrightz

water resistant and can be mixed within the ice.

3. Add bottles and/or cans.

4. Add remaining ice.

Need help?

Do you have a question about the Brightz CoolerBrightz and is the answer not in the manual?

Summary

Battery Replacement and Safety

Battery Replacement Procedure

Instructions for removing and replacing batteries in the LED module.

Safety Precautions

Warnings about battery mixing, choking hazards, and button cell battery risks.

The CoolerBrightz™ is an illuminated device designed to enhance the visual appeal of coolers, particularly when filled with ice and beverages. It provides an "awesome glow" and is water-resistant, making it suitable for direct contact with ice.

Function Description:

The primary function of the CoolerBrightz™ is to provide illumination within a cooler, creating a visually appealing effect. It features a color-changing mode that can be initiated by pressing the top center of the device. Users can also stop the color change on a desired color by pressing the top center again. To turn off the device, the top center is pressed once more after the color has been stopped. The device is designed with a battery-saving feature, automatically turning off after 3 hours of operation.

Important Technical Specifications:

Power Source: The CoolerBrightz™ is powered by two CR2050 (3V) batteries.
Water Resistance: The device is water-resistant, allowing it to be placed directly within or underneath ice in a cooler.
Automatic Shut-off: Features an automatic shut-off after 3 hours to conserve battery life.

Usage Features:

Operation:
- To turn on and start color changing: Press the top center of the device.
- To stop on a desired color: Press the top center again while the colors are changing.
- To turn off: Press the top center again after the color has been stopped.
Installation (Easiest Method):
1. Add a layer of ice to fill the bottom half of the cooler.
2. Position the CoolerBrightz™ on top of this initial layer of ice. Its water-resistant nature allows it to be mixed within the ice.
3. Add bottles and/or cans to the cooler.
4. Add the remaining ice to fill the cooler.
Placement: The device is designed to be placed within or underneath ice for optimal visual effect.
Safety Warnings:
- Battery Safety: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nicad, ni-mh, etc.) batteries.
- Choking Hazard: Contains small parts and is not suitable for children under 3 years of age.
- Button/Coin Cell Battery Warning: This product contains button or coin cell batteries. Swallowing these batteries can cause severe internal chemical burns in as little as 2 hours and can be fatal. Used batteries should be disposed of properly according to local regulations. New and used batteries must be kept away from children. Immediate medical attention should be sought if batteries are suspected to have been swallowed or placed inside any part of the body.
- Intended Use: The CoolerBrightz™ is not intended for use directly in drinks, or in drink dispensing coolers or any beverage dispensing system.

Maintenance Features:

Battery Replacement:
1. Remove the top cap of the CoolerBrightz™.
2. Remove the LED module from the device.
3. Slide the old batteries out of the LED module, noting their polarity for correct re-installation.
4. Slide new batteries into the LED module, ensuring correct polarity.
5. Re-install the LED module into the CoolerBrightz™.
6. Replace the top cap.

The CoolerBrightz™ is a product of Brightz, Ltd., located at 8000 Yankee Road, Suite 225, Ottawa Lake, MI 49267. For further inquiries, they can be reached via email at info@brightz-ltd.com or their website at www.brightz-ltd.com.