What to do if the outgoing cooling water temperature is too low in my Brilix XHP 60?
If the temperature of outgoing cooling water is too low in your Brilix Swimming Pool Heater, it is probably caused by insufficient water flow. Check the volume of water flow and whether or not the water passes through.
What to do if my Brilix XHP 60 Swimming Pool Heater is not working?
If your Brilix Swimming Pool Heater isn't working, there could be a few reasons. First, check the cable connection and the circuit breaker to ensure there is a power supply. Alternatively, the heat pump may be in standby mode, in which case you should start it up. Also, the water temperature might have reached the set value, putting the heat pump in constant temperature mode; check the water temperature setting. If the heat pump has just started, wait several minutes before starting it up. Finally, defrosting might be in progress, indicated by a “defrosting” message on the LED display.
What happens during the first stage of the frost protection system of Brilix XHP 60?
During the first stage of the frost protection system of your Brilix Swimming Pool Heater, the pump will run automatically if the ambient temperature or the temperature of incoming water is too low.
What happens during the second stage of the frost protection system in my Brilix XHP 60?
During the second stage of the frost protection system in your Brilix Swimming Pool Heater, the heat pump will start heating automatically if the ambient temperature or the temperature of incoming water is too low.
Why is there a drop in water temperature when my Brilix XHP 60 Swimming Pool Heater is running in heating mode?
If you notice a drop in water temperature while your Brilix Swimming Pool Heater is running in heating mode, it could be due to several reasons. First, the incorrect mode might be selected, so correct the running mode. Second, the values may indicate a fault; in this case, replace the defective cable controller with the LED display, then check the condition after the change of the running mode, and check the inlet and outlet water temperature. Finally, a controller failure could be the cause, so replace the defective main controller.
What to do if my Brilix Swimming Pool Heater has a communication error?
If your Brilix Swimming Pool Heater shows a communication error, it is likely due to a wrong connection of cables. Check the connection of cables.
What to do if my Brilix Swimming Pool Heater shows an inlet and outlet temperature difference error?
If your Brilix Swimming Pool Heater displays an inlet and outlet temperature difference error, it may be caused by insufficient water flow or too low pressure difference. Check the volume of water flow and whether or not the water passes through.
What to do if my Brilix Swimming Pool Heater has a short run?
If your Brilix Swimming Pool Heater experiences a short run, it could be due to the fan not running, insufficient air ventilation, or a lack of coolant. Check the cable connections between the motor and the fan, and replace them if necessary. Also, check the location of the heat pump unit and remove any obstruction preventing good air ventilation. If the problem persists, replace or repair the heat pump unit.
What to do if there is too much ice on the evaporator of my Brilix XHP 60 Swimming Pool Heater?
If there is too much ice on the evaporator of your Brilix Swimming Pool Heater, it may be caused by insufficient air ventilation or a lack of coolant. Check the location of the heat pump unit and remove any obstructions preventing good air ventilation. If that doesn't resolve the issue, consider replacing or repairing the heat pump unit.
Why is my Brilix XHP 60 showing protection against high pressure?
If your Brilix Swimming Pool Heater indicates protection against high pressure, it may be due to too much coolant or insufficient air flow. To fix this, remove the excess coolant from the heat pump system and clean the air exchanger.
Graphical representations of heat output, input power, and COP versus air temperature for various models.
Table and diagram detailing the physical measurements of the heat pump models.
Diagrams showing the physical setup, water connections, and discharge bypass.
Guidelines for selecting the installation position and the role of chemical elements.
Detailed wiring diagrams for specific heat pump models (XHP 40, 60, 100, 140, 200).
Steps for initial start-up, winter preparation, and post-winter restart.
Overview of control display functions and how to identify operating parameters.
Details and ranges for various operating parameters (0-8) and their settings.
Further parameter settings (9-H), mode identification, and timer configuration.
Procedures for setting water temperature, clock, locking, and timer functions.
Table detailing fault codes, causes, and corresponding solutions for controller LED display errors.
Guide to troubleshooting common issues not indicated by error codes on the LED display.
Exploded view diagram and a comprehensive list of all heat pump components.
Visual identification of key and ancillary spare parts for the heat pump.
Cabling diagram example and instructions for replacing heat pump parts.
Information on warranty conditions, safe product disposal, and service claims.
General| Category | Swimming Pool Heater |
|---|---|
| Heating Capacity | 6 kW |
| Power Supply | 230 V / 50 Hz |
| Maximum Working Pressure | 3 bar |
| Temperature Range | 40 °C |
| Model | Brilix XHP 60 |
To Next Page
