What to do if there is a defect to the sensor for cooling capacitor in Brilix XHP 40 Swimming Pool Heater?
If there is a defect to the sensor for cooling capacitor in your Brilix Swimming Pool Heater, the sensor is either open or short-circuited. Check or replace the sensor.
Why is my Brilix XHP 40 Swimming Pool Heater showing protection against low pressure?
If your Brilix Swimming Pool Heater shows a protection against low pressure error, it could be due to several reasons: a lack of coolant, insufficient flow, or a clogged filter or capillary tubes. To resolve this, check the gas for leakage and add coolant if necessary. Also, clean the air exchanger. Finally, change the filter or replace the capillary tubes.
Why is my Brilix XHP 40 showing protection against high pressure?
If your Brilix Swimming Pool Heater indicates protection against high pressure, it may be due to too much coolant or insufficient air flow. To fix this, remove the excess coolant from the heat pump system and clean the air exchanger.
What to do if there is too much ice on the evaporator of my Brilix XHP 40?
If there is too much ice on the evaporator of your Brilix Swimming Pool Heater, it may be caused by insufficient air ventilation or a lack of coolant. Check the location of the heat pump unit and remove any obstructions preventing good air ventilation. If that doesn't resolve the issue, consider replacing or repairing the heat pump unit.
What to do if my Brilix Swimming Pool Heater has a short run?
If your Brilix Swimming Pool Heater experiences a short run, it could be due to the fan not running, insufficient air ventilation, or a lack of coolant. Check the cable connections between the motor and the fan, and replace them if necessary. Also, check the location of the heat pump unit and remove any obstruction preventing good air ventilation. If the problem persists, replace or repair the heat pump unit.
What to do if there is a defect to the temperature sensor for incoming water in Brilix XHP 40 Swimming Pool Heater?
If there is a defect to the temperature sensor for incoming water in your Brilix Swimming Pool Heater, the sensor is either open or short-circuited. Check or replace the sensor.
What to do if there is a defect to the sensor for capacitor heating in Brilix Swimming Pool Heater?
If there is a defect to the sensor for capacitor heating in your Brilix Swimming Pool Heater, the sensor is either open or short-circuited. Check or replace the sensor.
What to do if there is a defect to the temperature sensor for outgoing water in Brilix Swimming Pool Heater?
If there is a defect to the temperature sensor for outgoing water in your Brilix Swimming Pool Heater, the sensor is either open or short-circuited. Check or replace the sensor.
What to do if the outgoing cooling water temperature is too low in my Brilix XHP 40?
If the temperature of outgoing cooling water is too low in your Brilix Swimming Pool Heater, it is probably caused by insufficient water flow. Check the volume of water flow and whether or not the water passes through.
What happens during the first stage of the frost protection system of Brilix Swimming Pool Heater?
During the first stage of the frost protection system of your Brilix Swimming Pool Heater, the pump will run automatically if the ambient temperature or the temperature of incoming water is too low.
Details the horizontal EU design specifications for R410A, covering heating and cooling capabilities.
Provides a visual guide illustrating the recommended installation setup for the heat pump system.
Guidance on selecting an appropriate and well-ventilated location for installing the heat pump unit.
Highlights the importance of chemical element placement for the heater's service life, especially regarding chlorination.
Wiring diagram for connecting the heat pump models XHP 40, XHP 60, and XHP 100 to the power supply.
Wiring diagram for connecting the heat pump model XHP 140 to the power supply.
Wiring diagram for connecting the heat pump model XHP 200 to the power supply.
Essential measures to prepare the heat pump for winter to prevent damage and voiding the warranty.
Procedure for safely starting the heat pump after the winter season, including system checks.
Configuration for operating the heat pump solely in heating mode.
Explains the functions of the control display, including buttons for navigation and mode selection.
Guide on how to view operating parameters and real-time data via the LED display.
Instructions on how to determine the current operating mode and view various sensor readings.
Procedure for adjusting the desired water temperature setting.
Instructions on how to lock and unlock the control panel settings to prevent accidental changes.
Guide on setting the internal clock of the heat pump control system.
Procedure for setting the timer to activate the heat pump at a specific time.
Procedure for setting the timer to deactivate the heat pump at a specific time.
Lists common fault codes displayed on the controller, their causes, and recommended solutions.
Addresses operational issues and faults that occur without specific error codes displayed on the unit.
General| Brand | Brilix |
|---|---|
| Model | XHP 40 |
| Category | Swimming Pool Heater |
| Language | English |
To Next Page
