Table of Contents
1. General Guidelines . . . . . . . . . . . . . . . . . .1
1.1 Inspection . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Unpacking the Heater . . . . . . . . . . . . . . . .1
1.3 Unloading or Lifting the Heater . . . . . . . . . .1
1.4 Gas Inlet Connection . . . . . . . . . . . . . . . . .1
1.5 Electrical Power Supply . . . . . . . . . . . . . . . .1
1.6 Installation of Duct Connection Pops . . . . . .2
1.7 Heater Positioning . . . . . . . . . . . . . . . . . . .2
1.8 Installation of Internal Heaters . . . . . . . . . . .2
1.9 Installation of External Heaters . . . . . . . . . .2
2. StarPro Max/Plus Internal Model
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .3
2.1 Heater Dimensions . . . . . . . . . . . . . . . . . . .3
2.2 Service Clearances . . . . . . . . . . . . . . . . . . .3
2.3 Splitting Internal Model Heaters . . . . . . . . . .4
2.4 Changing the Return Air Pop Orientation . . .5
2.5 Internal Model Flueing Instructions . . . . . . .5
3. StarPro Max/Plus External Model
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .6
3.1 Heater Dimensions . . . . . . . . . . . . . . . . . . .6
3.2 Service Clearances . . . . . . . . . . . . . . . . . . .6
3.3 Reversing the Heater . . . . . . . . . . . . . . . . . .6
3.4 Installation of Pops . . . . . . . . . . . . . . . . . . .6
3.5 Installation of Flashing . . . . . . . . . . . . . . . .7
3.6 Installation of Flue Terminal . . . . . . . . . . . .7
3.7 Area to Cut in the Wall . . . . . . . . . . . . . . . .7
3.8 Flue Terminal Clearances . . . . . . . . . . . . . .7
4. StarPro B-Max Model Guidelines
4.1 Heater Dimensions . . .
. . . . . . . . . . . . . . . .8
4.2 Service Clearances . . . . . . . . . . . . . . . . . . .8
4.3 Installation of Flue Terminal . . . . . . . . . . . .8
4.4 Flue Terminal Clearances . . . . . . . . . . . . . .9
5. StarPro Max/Plus & B-Max
Installation of Thermistor . . . . . . . . . . . . .9
6. StarPro Max & B-Max Condensate Removal
(HX Models only) . . . . . . . . . . . . . . . . . . .10
7. StarPro Max/Plus & B-Max -
Zoning & Add-on Air Conditioning . . . .10
7.1 Wiring a Damper Motor to the Heater’s
Control Module . . . . . . . . . . . . . . . . . . . .11
8. Classic 2P Wombat Model Guidelines . .11
8.1 Heater Dimensions . . . . . . . . . . . . . . . . . .11
8.2 Service Clearances . . .
. . . . . . . . . . . . . . .11
8.3 Internal Flueing Instructions . . . . . . . . . . . .11
8.4 Splitting 2P Wombat Heaters . . . . . . . . . . .12
9. Classic Buffalo Model Guidelines . . . . . .12
9.1 Heater Dimensions . . . . . . . . . . . . . . . . . .12
9.2 Installation of Flashing . . . . . . . . . . . . . . .12
9.3 Service Clearances . . . . . . . . . . . . . . . . . .12
9.4 Flue Terminal Clearances . . . . . . . . . . . . .12
10. Classic Upflow/Downflow Model
Guidelines . . . . . . . . . . . . . . . . . . . . . . . .13
10.1 Heater Dimensions . . . . . . . . . . . . . . . . . .13
10.2 Service Clearances . . . . . . . . . . . . . . . . . .13
10.3 Ventilation for Inside Heaters . . . . . . . . . . .13
10.4 Internal Flueing Instructions . . . . . . . . . . . .13
11. Ducting Inform
ation . . . . . . . . . . . . . . . .13
12. Outlet Guide . . . . . . . . . . . . . . . . . . . . . .14
13. Thermostat Installation . . . . . . . . . . . . . .15
13.1 Brivis Networker Installation . . . . . . . . . . .16
13.2 Brivis Programmable and Brivis Manual
Thermostat Installation . . . . . . . . . . . . . . .18
13.3 Add-On Refrigerative Air-Conditioning on
Classic Heaters . . . . . . . . . . . . . . . . . . . .19
14. Commissioning and Control Settings . . .19
14.1 StarPro Max/Plus & B-Max
Heater Control Settings . . . . . . . . . . . . . . .19
14.2 StarPro Max/Plus & B-Max
Commissioning Instructions . . . . . . . . . . . .21
14.3 Classic Commissioning Instructions . . . . . .23
15. Technical Specifications . . . . . . . . . . . . . .24
To Next Page
Loading...
Need help?
General
