Brother Entrepreneur PR650e User Manual (English)

Other manuals for Brother Entrepreneur PR650e

Questions and Answers:

S
Stacey GarzaAug 17, 2025
Why does the needle keep breaking on my Brother Entrepreneur PR650e?
- T
  thomasstevenAug 17, 2025
  The needle may break due to several reasons: * Incorrect installation: Ensure the needle is correctly installed. * Loose screw: Tighten the needle set screw using the Allen screw driver. * Damaged needle: Replace the needle if it's bent or blunt. * Damaged needle plate: If the area around the needle plate hole is damaged, consider replacing the needle plate. * Needle hitting the plate: Replace the needle or consult your nearest authorized dealer. * Incorrect presser foot position: Consult your nearest authorized dealer.
A
Andrew EricksonAug 19, 2025
Why does the upper thread keep breaking on my Brother Sewing Machine?
- P
  Paul ReynoldsSep 12, 2025
  The upper thread may break because: * The needle is not correctly installed. Make sure to correctly install the needle. * The needle set screw is loose. Use the Allen screw driver to tighten the needle set screw. * The needle is bent or blunt. Replace it with a new one. * The area around the hole in the needle plate is damaged. Replace the needle plate or consult your nearest authorized dealer. * You are using a weak thread. Slow down the machine sewing speed.
R
Rachel WoodsAug 22, 2025
What to do if my Brother Sewing Machine is skipping stitches?
- E
  Eric HoffmanAug 22, 2025
  Skipped stitches can occur if: * The upper thread isn't threaded correctly, so thread it correctly. * The needle is bent or blunt, so replace it with a new one. * The needle is not installed correctly, so correctly install the needle. * Dust has accumulated under the needle plate or in the hook, so clean the hook and the needle plate.
J
John GreerAug 25, 2025
How to fix a noisy Brother Entrepreneur PR650e?
- L
  laratravisAug 26, 2025
  A noisy machine could be due to: * Lint wound in the hook. Clean the hook. * The upper thread not threaded correctly. Check the thread path, and then thread the upper thread again. * Not enough oil applied. Oil recommended parts.
S
Sharon SimmonsAug 28, 2025
What to do if the bobbin thread breaks on my Brother Entrepreneur PR650e?
- T
  taylorjodiAug 28, 2025
  If the bobbin thread breaks, check the following: * Ensure the bobbin thread is correctly threaded. * Replace the bobbin if it's scratched or doesn't rotate smoothly. * Replace the bobbin case if it's damaged. * Remove any tangled thread and clean the hook.
D
David JeffersonAug 30, 2025
How to fix loops in the upper thread of my Brother Sewing Machine?
- D
  David AndersonAug 30, 2025
  Loops in the upper thread may appear because: * The upper thread tension is low. After passing the upper thread through the hole in the presser foot, pull the thread by hand to check the thread tension. * The thread quality is poor. Try sewing with different thread. If the problem no longer occurs after the thread is changed, the thread quality is the problem. Replace the thread with one of good quality.
S
smithleslieSep 2, 2025
Why is my Brother Embroidery Machine not operating?
- R
  Rebecca MossSep 2, 2025
  The embroidery machine might not be operating because: * The machine is not turned on. Turn on the embroidery machine. * The machine has not been unlocked. Touch the unlock key. * The start/stop button was not pressed. With the machine unlocked, press the start/stop button.
L
Lauren SampsonSep 5, 2025
What to do if my Brother Entrepreneur PR650e shows a broken thread error when the thread isn't broken?
- J
  john08Sep 5, 2025
  This error can occur if the thread breakage sensor in the thread tension disc of the thread tension knobs cannot detect that the thread is being fed, even if the machine is running. Clean the tension unit and correctly pass the thread through the thread tension disc.
J
jamesthompsonSep 7, 2025
Why doesn't the upper thread reach the bobbin thread when my Brother Entrepreneur PR650e starts embroidering?
- J
  James PageSep 7, 2025
  The upper thread may not reach the bobbin thread if there is no more thread in the bobbin, the thread does not feed from the bobbin, or the thread that is fed from the bobbin is too short. Correctly thread the lower thread.
H
hamiltonrhondaSep 10, 2025
Why does my Brother Entrepreneur PR650e make needle cuts or holes in the garment?
- S
  Scott MitchellSep 10, 2025
  Needle cuts or holes in the garment are caused if the needle is dull. Replace the needle. Dull needles have a difficult time passing through the garment, causing fabrics to tear.