Brother MFC-T910DW - Quick Setup Guide Manual

Watch our FAQ Videos for help
with setting up your Brother
machine.
support.brother.com/videos
BK (Dye)CMY
BTD60BK
BT5000CMY
BT5001CMY
BT5009CMY
DO NOT USE
BK (Pigment)
BT6000BK
BT6001BK
BT6009BK
1
2
3



Remove the cap and protective
film from the ink bottle, and then
replace the cap.
NOTE
Fasten the ink bottle cap tightly to
avoid leakage.
Open the ink tank cover a and pull
the tab
b downwards to open the
cap of the ink tank.
1
2
IMPORTANT
NOTE
• The Reference Guide for this model is available on the enclosed installation disc.
• Save all packing materials and the box in case you must ship your machine.
• You must purchase the correct interface cable for the interface you want to
use. A USB cable is included for some countries.
USB cable
We recommend using a USB 2.0 cable (Type A/B) that is no more than 6 feet
(2 meters) long.
Ethernet (Network) cable
Use a straight-through Category 5 (or greater) twisted-pair cable for 10BASE-T or
100BASE-TX Fast Ethernet Network.
2
Load paper in the paper tray
For more information about paper handling and sizes, see the Reference Guide.
1
Unpack the machine and check the components
The components included in the box may differ depending on your country.
Remove the protective tape and film covering the machine and the ink tank cover.
When the machine has finished the initial cleaning
process, follow the steps on the LCD to configure the
machine settings.
• Check print quality
• Congurethetraysettings
• Set Firmware Update Notice
• Print the installation sheet
Connect the power cord and the
machine powers on automatically.
Follow the prompts displayed on the
LCD to set the date and time.
NOTE
If you are sharing one telephone line with an external
telephone, connect it as shown below. Before you
connect the external telephone, remove the white
protective cap c from the EXT. jack of the machine.
a. Extension telephone
b. External telephone
c. Protective cap
Quick Setup Guide
MFC-T910DW
Read the Product Safety Guide first, then read this Quick Setup Guide
for the correct installation procedure.
3
Connect the
power cord
4
Fill the ink tanks with the starter ink
5
Machine settings
ME X /LTN - ENG
Version A
Starter Ink Bottles
• Black
• Yellow
• Cyan
• Magenta
Quick Setup Guide
Product Safety Guide
Brother Installation Disc
USB Interface Cable
(For some countries)
Telephone Line Cord
The correct Receive Mode is
determined by the external
devices and telephone subscriber
services (Voice Mail, Distinctive
Ring, etc.) you will be using on the
same line as the Brother machine.
For more information, see Choose
the Correct Receive Mode in the
Reference Guide.
1. Press Ajustes (Settings).
2. Press a or b to select the following:
a. Select [Conf. inicial](Initial Setup), and then
press OK.
b. Select [Sel. idioma](Local Language), and
then press OK.
c. Select your language, and then press OK.
3. Press Detener/Salir (Stop/Exit).
1. Press Ajustes (Settings).
2. Press a or b to select the
following:
a. Select [Fax], and then
press OK.
b. Select [Setup Receive],
and then press OK.
c. Select [Receive Mode],
and then press OK.
d. Select your Receive Mode,
and then press OK.
3. Press Detener/Salir (Stop/
Exit).
Store your name and fax
number so the machine prints it
on all outgoing fax pages.
For more information, see Enter
Text on Your Brother Machine in
the Online User’s Guide.
1. Press Ajustes (Settings).
2. Press a or b to select the following:
a. Select [Initial Setup],
and then press OK.
b. Select [Station ID],
and then press OK.
c. Select [Fax], and then
press OK.
3. Enter your fax number (up to 20 digits),
and then press OK.
4. Enter your name (up to 20 characters),
and then press OK.
5. Press Detener/Salir (Stop/Exit).
7
Select your
language (if needed)
9
Set your Station ID
If you are not using your machine as a fax, go to
10
.
6
Connect the telephone line cord
If you are not using your machine as a fax, go to
7
.
8
Select the correct
Receive Mode
If you are not using your machine as a fax, go to
10
.
The latest manuals are available at the Brother Solutions Center:
support.brother.com/manuals
Check the ink bottle model name
on the label. Incorrect ink may
cause damage to the machine.
Connect the telephone line cord.
Use the jack marked LINE.
Pull the paper tray completely
out of the machine.
Open the output paper tray
cover a. Fan the paper well and load it in the tray.
Close the output paper tray cover, and
then slowly push the tray completely
into the machine.
Adjust the paper guides.
NOTE
Pull out the paper support a, and unfold
thepapersupportapb so that the
printed pages do not fall.
Remove the tip of the ink bottle.
Insert the nozzle of the ink bottle
firmly so that the ink does not
spill. Fill the ink tank by gently
squeezing the bottle as shown.
Empty the entire bottle into the
ink tank.
Push down on the cap of the ink
tank to close it tightly. Repeat step
4
for the three other ink tanks.
Close the ink tank cover. The
machine will prepare the ink tube
system for printing.
Point the nozzle upward so
that the ink does not spill,
and then remove the nozzle
from the ink tank.