To Next PageTo Next PageWhy is my Brother Label Maker label not ejecting properly?
If the label is not ejecting properly from your Brother Label Maker after printing, check that the ejection path is not blocked. Additionally, verify that the RD Roll is set correctly by removing and reinstalling it, and ensure the RD Roll compartment cover is closed properly.
How to reset data on Brother Label Maker?
To reset your Brother Label Maker and delete data transferred from a PC, first turn the machine off by pressing and holding the ON/OFF button. While still holding the ON/OFF button, press the Cut button six times.
How to cancel print job on Brother TD-4000 Label Maker?
To cancel the current printing job on your Brother Label Maker, ensure the printer is turned on, then press the ON/OFF button.
How to improve print quality on Brother Label Maker?
If the print quality of your Brother Label Maker is poor, clean the roller.
How to fix cutter error on Brother TD-4000?
To resolve a cutter error on your Brother Label Maker, keep the RD roll compartment cover closed and press the ON/OFF button.
What to do if the label is not ejected properly after printing Brother?
If labels are not ejected properly from your Brother Label Maker after printing, check the following: * Ensure the ejection path of the label is not blocked. * Remove and reinstall the RD Roll to ensure it is set properly. * Make sure the RD Roll compartment cover is closed properly.
What to do if Brother Label Printer TD-4000/4100N does not print?
If your Brother TD-4000/4100N Label printer is not printing or you are receiving a printing error, try the following: * Ensure the cable is securely connected. * Remove and reinstall the RD Roll. * Check that enough roll remains. * Confirm that the RD Roll compartment cover is closed. * Turn the printer off and on again. If the problem persists, contact Brother Customer Service at 1-800-255-0415. * Move the guide against the side of the RD Roll. * Feed the media under the gap sensor.
What to do if error occurred when roll cannot be fed to the beginning of the label on Brother Label Maker?
To clear the error, press the Feed button again.
What to do if I get a cutter error on Brother TD-4000?
If your Brother Label Maker is experiencing a cutter error, keep the RD roll compartment cover closed and press the ON/OFF button. Also, inspect the cutter unit and remove any paper jam.
How to reset Brother TD-4000 and delete transferred data?
To reset your Brother Label Maker and delete the data transferred from your PC, first turn the machine OFF by pressing and holding the ON/OFF button. Then, hold down the ON/OFF button again for two seconds. While still holding the ON/OFF button, press the Cut button six times.
General| Print technology | Direct thermal |
|---|---|
| Vertical printing | Yes |
| Maximum resolution | 300 x 300 DPI |
| Label type | RD |
| Network ready | No |
| Dimensions (WxDxH) | 173 x 229 x 158 mm |
| Standard interfaces | RS-232C |
| Tape cutting | Automatic |
| Internal memory | 2 MB |
| Number of fonts | 5 |
| Number of styles | 9 |
| Built-in barcodes | Codabar (NW-7), EAN13, EAN8, Maxicode, Postnet, QR Code, UPC-A, UPC-E |
| Power requirements | 220-240VAC, 50/60 Hz, 1.8A |
| Minimum RAM | 128 MB |
| Minimum storage drive space | 70 MB |
| Compatible operating systems | Windows XP/7, Windows Vista |
| Bundled software | P-touch PT-Editor 5.0, Transfer Manager 2.1, Transfer Express, Library 2.1 |
| Media thickness | 0.08 - 0.155/0.170 mm |
| Maximum label width | 102 mm |
| Maximum label length | 3 m |
| Maximum roll diameter | 101.6 mm |
| Product color | Gray |
| Operating temperature (T-T) | 10 - 35 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Harmonized System (HS) code | 84433210 |
Weight and Dimensions| Depth | 229 mm |
|---|---|
| Width | 173 mm |
| Height | 158 mm |
| Weight | 1810 g |
