3. Insert the Tape Cassette
• After the tape passes under the Tape Guide, pull the tip
to remove any slack in the tape.
• Make sure the tape is not caught in the Label Printer
when inserting or removing the Tape Cassette.
1. Insert the Tape Cassette following the illustration under
the Tape Cassette Compartment Cover. Conrm that the
tip of the tape is pointed at the Tape Exit Slot.
2. Press the Tape Cassette into the Label Printer until
it locks into place, and then close the Tape Cassette
Compartment Cover.
End of tape
Tape Guide
4. Turn the Power ON or OFF
To print from the Label Printer, go to
1. Print from the Label Printer
To print from your computer, go to
2. Print from Your Computer
To print from your mobile device, go to
3. Print from Your Mobile Device
Power on
Press
.
Power off
Press and hold
until the Label
Printer turns off.
PT-D460BT
D460BT
Thank you for purchasing the PT-D460BT (hereafter referred to as “the Label Printer”). Your
PT-D460BT produces professional, high-quality, durable labels. In addition, the variety of tape
cartridges available allows you to print labels with different widths and exciting colours.
Please read this guide, including the Product Safety Guide section, before using this Label Printer.
After reading this guide, keep it in a safe place.
For FAQs, troubleshooting, and to download software and manuals, visit support.brother.com.
Supplies
Brother TZe Tape Cassette Available widths: 3.5 mm, 6 mm, 9 mm, 12 mm, 18 mm
Head Cleaning Tape Cassette TZe-CL4
2. Install Batteries or Connect the AC Adapter
Remove the protective material (rst use only) before using the Label Printer.
Batteries
AC Adapter
• When using the AC Adapter (AD-E001A):
- Insert the Adapter cord connector into the AC Adapter
Jack on the side of the printer.
- Insert the plug into the nearest standard electrical
socket. For memory backup, we recommend using AA
alkaline batteries (LR6) together with the AC Adapter.
• To safeguard and back up the Label Printer’s memory,
when the AC Adapter is unplugged, keep AA alkaline
batteries (LR6) installed in the Label Printer.
• When power is disconnected for more than two minutes,
all text and format settings will be cleared. Any text les
stored in the memory will also be cleared.
• Remove the batteries if you do not intend to use the
Label Printer for an extended period of time.
• Dispose of the batteries at an appropriate collection
point, not in the general waste stream. In addition, be
sure to observe all applicable federal, state, and local
regulations.
• When storing or discarding the batteries, wrap them
(for example with cellophane tape), to prevent them from
short-circuiting.
(Battery insulation example)
1. Cellophane tape
2. Alkaline battery
1
2
3. Print from Your Mobile Device
Application Installation
Download the following application from the App Store or Google Play™:
Brother
iPrint&Label
Create labels for business use, including
barcodes, ofce equipment labels, and folder
tab labels.
Support Center
App
This app provides access to setup
information, product manuals, FAQs,
and troubleshooting tips.
To save tape, enable the Chain Printing setting in Brother iPrint&Label.
Print your labels and leave the last label in the Label Printer until you are ready to print
a new label.
How to enable or disable Bluetooth
1. Check that the printer is on.
2.
[Settings] / [Bluetooth] / [Bluetooth (On/
Off)]
/ [On]/[Off] /
Pair the Label Printer with Your Mobile Device via Bluetooth
PT-D460BT
1. Go to your mobile device’s settings
menu and enable the Bluetooth
option.
2. Use the pairing number displayed
on the Application Download Label
attached to the front of the Label
Printer.
• If the printer prompts you to enter a PIN, enter “0000”.
• Pairing instructions may differ slightly, depending on your mobile device.
• If your mobile device cannot discover the printer via Bluetooth, check the following:
- Place your mobile device as close as possible to the Label Printer.
- Make sure there are no obstacles or items that emit radio waves, such as a
microwave oven, between the Label Printer and your mobile device.
• If a Bluetooth pass key appears on the Label printer’s LCD during pairing, make sure
your mobile device displays the same Bluetooth pass key, and then press [OK].
• This Label Printer does not support Wi-Fi connections.
1. Print from the Label Printer
STEP
1. Overview
D460BT
Starter
Tape Cassette
USB Cable
AC Adapter
Tape Viewer
1. Caps mode
2-7. Font Style Icons
8. Label Width x Label Length
9. Block number
10. Line number
11. Cursor
12. Return mark
Tape Cassette
Compartment
Cover
Tape Exit Slot
LCD
Keyboard
Power
Preview
Application Download Label
Tape Cutter
Lever
AC Adapter Jack
USB Port
1
9
10
11 12
2 3 4 5 6 7 8
The components included in the box may differ depending on your country or region.
Serial Number Location
Serial Number
Before Use
Use the Label Printer
Safety Precautions
Be sure to read this section before using the product. It contains important safety instructions.
We recommend that you keep this document nearby for future reference.
• For servicing, adjustments, or repairs, contact Brother customer service or your local Brother dealer.
• If the product operates abnormally or any error occurs, or if any cable is damaged, turn the product off,
disconnect all cables, and contact Brother customer service or your local Brother dealer.
• We assume no responsibility for damages arising from earthquakes, re, other disasters, actions of third
parties, the user’s intentional or negligent operation, misuse, or operation under other special conditions.
• We assume no responsibility for damage (such as losses, loss of business prot, lost prots, business
disruptions, or a lost means of communication) that may result from the use of, or inability to use, the
product.
• We assume no responsibility for damages that may result from incorrect operation of the product by
connecting incompatible equipment or using incompatible software.
• We assume no responsibility for any damages or lost prot arising from the use of labels created with this
product, the disappearance or change of data due to failure, repair, or consumables and we do not accept
any claim from a third party.
• Brother reserves the right to make changes without notice in the specications and materials contained
herein. Furthermore, Brother shall not be responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to typographical and other errors relating to
the publications.
• For more information about the available software, see the User’s Guide on the Brother support website at
support.brother.com.
• The latest version of your product documentation is available on the Brother support website at
support.brother.com.
• The available models, accessories, and supplies may vary depending on the country or region.
• This product is approved for use in the country or region of purchase only.
WARNING
CAUTION
Failure to observe instructions and warnings could result in minor or moderate injuries.
Label Printer, USB Cable, AC Adapter, Alkaline Batteries
• Use only the specied AA alkaline batteries (LR6).
• DO NOT use combinations of old and new batteries or combinations of different types, charging levels,
manufacturers, or models.
• DO NOT drop the Label Printer when removing it from the box or relocating it, otherwise you may get
injured.
• Be careful when closing the Tape Cassette Compartment Cover. There is a risk of injury if your nger gets
pinched between the upper and lower parts of the cover.
• When you are not using the Label Printer, store it out of the reach of children. In addition, do not allow
children to put the Label Printer parts or labels in their mouths. If any object has been swallowed, seek
medical attention immediately.
• DO NOT leave the Label Printer or any tape within the reach of babies and children.
• Store the Label Printer on a at, level, and stable surface.
• Remove the batteries and disconnect the AC Adapter if you do not intend to use the printer for an extended
period of time.
• DO NOT press on the Liquid Crystal Display (LCD).
• When disconnecting the AC Adapter from the electrical socket, always hold the AC Adapter.
• DO NOT overload an electrical circuit with the AC Adapter.
• DO NOT open the Tape Cassette Compartment Cover when operating the Cutter unit.
• DO NOT apply excessive pressure to the Cutter unit.
Product Safety Guide
Regulation
Declaration of Conformity (Europe/Turkey only)
We, Brother Industries, Ltd.
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561 Japan
declare that these products are in conformity with the relevant EU harmonization legislation
(Europe/Turkey only) and UK legislation (Great Britain only).
The Declaration of Conformity (DoC) can be downloaded from the Brother support website.
Visit support.brother.com/manuals.
UK Declaration of Conformity for Radio Equipment Regulation 2017 (Great Britain only)
(Applicable to models with radio interfaces)
We, Brother Industries, Ltd.
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561 Japan
declare that these products are in conformity with the provisions of the Radio Equipment
Regulation 2017. A copy of the Declaration of Conformity can be downloaded by following the
instructions in the Declaration of Conformity (Europe/Turkey only) section.
EU Declaration of Conformity for RE Directive 2014/53/EU (Europe/Turkey only)
(Applicable to models with radio interfaces)
We, Brother Industries, Ltd.
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561 Japan
declare that these products are in conformity with the provisions of the RE Directive 2014/53/EU.
A copy of the Declaration of Conformity can be downloaded by following the instructions in the
Declaration of Conformity (Europe/Turkey only) section.
CAUTION
RISK OF EXPLOSION IF BATTERIES ARE REPLACED WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Bluetooth
This printer supports Bluetooth.
Frequency bands: 2400 MHz - 2483.5 MHz
Maximum radio-frequency power transmitted in the frequency bands:
Less than 20 dBm (e.i.r.p)
Information for compliance with Commission Regulation 801/2013
PT-D460BT
Power consumption* 0.7W
* All network ports activated and connected
2. Print from Your Computer
Windows
In your browser’s address bar, type install.brother and download
and install the Printer Driver and P-touch Editor by following the
on-screen instructions.
Mac
Download P-touch Editor from the App Store to print from your
Mac. You do not need to download and install any drivers.
http://install.brother
• When printing from your computer, you must connect the Label Printer and computer
with the included USB Cable or via Bluetooth connection.
• This Label Printer does not support Wi-Fi connections.
Software Features
Printer Driver
Software required to print from a Label Printer using a Windows
computer.
P-touch Editor
Label creation software for computers. This application comes
with built-in drawing tools that allow you to print a wide variety of
custom labels in complex layouts with text of different fonts and
styles, frames, imported images, barcodes, and more.
D026K9001
The keyboard layout may vary by country.
The default language is “English”
To Next Page
Loading...
