How to fix Brother XR9500PRW that does not work?
If your Brother Sewing Machine isn't working, there are several things to check: * Ensure the machine is plugged in. * Make sure the main power switch is turned on. * Verify the bobbin winder shaft is moved to the left. * Confirm you are using the foot controller properly.
How to adjust the thread tension on a Brother XR9500PRW Sewing Machine?
If the thread tension on your Brother Sewing Machine is incorrect, try the following: * Correct the upper threading. * Wind the bobbin thread properly. * Choose a thread and needle appropriate for the fabric. * Attach the presser foot holder properly. * Adjust the tension of the upper thread. * Reset the bobbin thread correctly.
How to prevent skipped stitches on a Brother XR9500PRW Sewing Machine?
If you're experiencing skipped stitches on your Brother Sewing Machine, try these steps: * Correct the upper threading. * Choose the right combination of fabric, thread, and needle. * Replace the needle if it's bent or blunt. * Remove the needle plate cover and clean the plate and the bobbin case to eliminate any accumulated dust.
Why isn't the fabric feeding through my Brother Sewing Machine?
If the fabric does not feed through your Brother Sewing Machine, ensure that the feed dogs are not lowered by sliding the feed dog position lever. Also, the stitch might be too fine, so try lengthening the stitch length.
Why does the needle break on my Brother Sewing Machine?
If the needle on your Brother Sewing Machine is breaking, consider the following: * Ensure the needle is fitted properly. * Tighten the needle clamp screw firmly with a screwdriver. * Replace the needle if it's bent or blunt. * Use the correct combination of fabric, thread, and needle. * Attach the correct presser foot for the stitch type. * Loosen the upper thread tension. * Use only bobbins designed for this machine.
Why does the upper thread keep breaking on my Brother Sewing Machine?
If the upper thread on your Brother Sewing Machine keeps breaking, here’s what you should check: * Make sure you've threaded the upper thread correctly. * Ensure the needle is appropriate for the thread you're using. * Loosen the upper thread tension. * Remove any tangled thread, especially in the bobbin case, and clean the bobbin case if necessary. * Replace the needle if it's bent or blunt.
What causes the lower thread to tangle on a Brother XR9500PRW?
If the lower thread is tangling or breaking on your Brother Sewing Machine, make sure you wind the bobbin thread properly and reset the bobbin thread correctly.
Why is my Brother XR9500PRW Sewing Machine making a high-pitched noise?
To address a high-pitched noise while sewing with your Brother Sewing Machine: * Clean the bobbin case. * Correct the upper threading. * If the bobbin case is scratched, replace it and contact your retailer or the nearest authorized service center.
Why is the upper thread too tight on my Brother XR9500PRW?
If the upper thread is too tight on your Brother Sewing Machine, it might be because the bobbin thread is incorrectly installed. Make sure to correctly install the bobbin thread.
What to do if the fabric is wrinkled when using Brother Sewing Machine?
If the fabric is wrinkling when using your Brother Sewing Machine, consider these solutions: * Thread the upper thread and wind the bobbin thread properly. * Use the right combination of fabric, thread, and needle. * Replace the needle if it is bent or blunt.
General| Buttonhole Styles | 8 |
|---|---|
| Maximum Stitch Width | 7 mm |
| Maximum Stitch Length | 5 mm |
| LCD Display | Yes |
| Needle Threader | Automatic |
| Bobbin Type | Drop-in |
| Speed Control | Yes |
| Drop Feed | Yes |
| Free Arm | Yes |
| Type | Computerized |
| Included Accessories | Wide table, seam ripper, cleaning brush, needles, bobbins, screwdriver, spool caps |
| Presser Feet | Buttonhole foot, Overcasting foot, Monogramming foot, Zipper foot, Zigzag foot, Blindstitch foot, Walking foot, Quilting foot |
| Warranty | 25 years limited warranty |
To Next Page
