To Next PageTo Next PageHow to fix no mass flow rate on Bürkert MFM?
If there is no mass flow rate on your Bürkert MFM, it might be because the pipes are too large or not fully vented. To fix this, vent the pipes or change the pipe diameter.
Why is the product status indicator yellow on my Bürkert MFC Analogue Controller?
If the product status indicator on your Bürkert MFC Analogue controller is yellow, it could be due to several reasons: * One of the values is out of specification, potentially damaging the sensor or product. Operate the product within specifications. If the indicator remains yellow, return the product to Bürkert. * The set-point position for the control valve has almost reached 100%, and the set-point value cannot be reached. Increase the inlet pressure or decrease the back pressure. Reduce the pressure drop if it's too high in the pipe. If the filters in the pipe are dirty, clean them.
Why is the LED red and flashing or red and ON on my Burkert product?
If the LED on your Burkert product is red and flashing, or red and ON, it could be due to a few reasons: * The fluid or ambient temperature may be too high. Ensure you respect the maximum ambient and fluid temperatures. * Restart the product to turn off the red flashing LED by de-energizing and then re-energizing it. * A cable might be broken. Check that the electrical connections between the product housing and the motor valve are secure.
What to do if the set-point value is not reached on my Bürkert MFC?
If the set-point value is not being reached on your Bürkert MFC, it could be due to a few reasons: * The mesh filter might be clogged. Try cleaning or replacing it. * The inlet pressure could be too low. Increase it to the calibration pressure value. * The outlet pressure might be too high. If the fluid connection pipes after the product are dirty, clean them.
Why is the product status indicator red on my Bürkert MFM Analogue Controller?
If the product status indicator on your Bürkert MFM Analogue controller is red, it could be because the supply voltage is outside the error range, potentially damaging the product. To resolve this, operate the product within the specified limits. If the indicator remains red, return the product to Bürkert for further assistance. In some cases, maintenance may be needed, so contact the manufacturer.
What to do if the product status indicator is red on my Bürkert MFM Ethernet Controller?
If the product status indicator on your Bürkert MFM Ethernet controller is red, here are a few potential causes and solutions: * The supply voltage may be outside the acceptable range, which can damage the product. Ensure the product operates within the correct specifications. If the indicator remains red, return the product to Bürkert. * The Ethernet product variant might not be correctly connected to the PLC. Check the wiring and the PLC status. If using the EtherCAT protocol, verify that the incoming cable is in the ETH1 port and the outgoing cable is in the ETH2 port. * The sensor, internal memory, or the product itself might be defective, requiring maintenance. Contact the manufacturer in this instance.
What to do if the product status indicator is red on my Bürkert MFC Analogue Controller?
If the product status indicator on your Bürkert MFC Analogue controller is red, it could be due to a few reasons: * The supply voltage is out of the error range, which can damage the product. Make sure the product operates within the specifications. If the indicator stays red, send the product back to Bürkert. * The Autotune may be incorrect or aborted. Ensure fluid flows through the product and try the Autotune again. * The sensor, internal memory, or the product may be defective, requiring maintenance. In this case, contact the manufacturer.
General| Communication Protocol | Ethernet |
|---|---|
| Power Supply | 24 V DC ±10% |
| Operating Temperature | 0 to +50 °C |
| Protection Class | IP65 |
| Type | Mass Flow Controller |
| Protocol | Modbus TCP |
| Media | Gases |
| Storage Temperature | -20 to +60 °C |
| Housing Material | Stainless steel, Aluminium |
