What does 'W. BATCH' mean on my Burkert SE35?
If the device state LED on your Burkert Controller is orange and displays the message 'W. BATCH', it means the number of completed dosings has reached the value specified in the 'BATCH-W.' parameter of the Test menu. To address this, perform the planned maintenance operation and reset the daily totalizer of the completed dosings.
What to do if my Bürkert Measuring Instruments display shows 'LOW BATT'?
If your Bürkert Measuring Instruments display shows 'LOW BATT,' it means the battery power is too low and the device isn't working. You should replace the batteries.
What does "MEAS. OVF" mean on Bürkert Measuring Instruments and how to fix it?
If the Bürkert Measuring Instruments shows 'MEAS. OVF', the rotational frequency of the paddle wheel is higher than 250 Hz. Check and adjust the flow rate in the pipe if necessary.
What does 'Process level' mean on my Burkert SE35?
If your Burkert Controller's device state LED displays any colour with the message 'Process level', it indicates that the power supply was cut during the consultation of the messages of the Information menu via the digital inputs. Ensure that the PLC recognizes that the device has returned to the Process level.
What does 'WARN. VOL.' mean on my Burkert Controller?
If the device state LED on your Burkert Controller is orange and displays the message 'WARN. VOL.', it indicates that the daily volume or mass totalizer has reached the value set in the 'VOLUME-W.' parameter of the Test menu. Perform the planned maintenance operation and reset the daily volume or mass totalizer.
Why is the displayed quantity increasing slowly on my Burkert SE35 Controller during dosing?
If, during a dosing process, the displayed quantity on your Burkert Controller increases or decreases very slowly and the device state LED is green, check that the K-factor corresponds to the fitting used. You may also perform a Teach-In procedure to determine the K-factor of the fitting used and check that the flow rate in the pipe is high enough.
Why does my Bürkert Transmitter show 'PU H LIM'?
If the Bürkert Transmitter displays 'PU H LIM', it means that the pulse value times the K-factor of the device is greater than 1000000, indicating that the entered volume for a pulse is too high. To fix this, enter a lower volume per pulse and check the K-factor value.
Why does my Bürkert Transmitter show 'PU L LIM'?
If your Bürkert Transmitter displays 'PU L LIM', it indicates that the pulse value times the K-factor of the device is less than 1, meaning the entered volume for a pulse is too low. To resolve this, enter a higher volume per pulse and check the K-factor value.
Why doesn't the dosing start on my Burkert SE35, even when the procedure is correctly initiated?
If the dosing does not start on your Burkert Controller even though the procedure has been correctly initiated and the device state LED is green, it could be due to either of the following reasons: * The dosing quantity times the set K-factor is lower than 6. * The pipe diameter is too high for dosing small quantities. To resolve this: * Set a dosing quantity that is higher or equal to 6 divided by the set K-factor. * Reduce the pipe diameter.
Why is the displayed flow rate always nil on my Bürkert Measuring Instruments?
If the displayed flow rate on your Bürkert Measuring Instruments is always nil, ensure the flow rate in the pipe is not nil, check that the entered K factor is correct. Also, consider choosing a smaller flow rate unit or increasing the number of displayed decimals.
Lists environmental, electrical, and fluid specifications for the compact model.
Lists environmental, electrical, and fluid specifications for the panel model.
Lists environmental, electrical, and fluid specifications for the wall-mounted model.
Lists environmental, electrical, and fluid specifications for the SE35 Batch.
Lists environmental, electrical, and fluid specifications for the 8035 Batch.
Lists technical specs for SE35 Batch with specific sensor-fittings.
Crucial safety guidelines for the fluid installation process.
Step-by-step instructions for installing the 8025 Batch in its compact form.
Step-by-step instructions for installing the 8035 Batch.
Critical safety measures for electrical connections and wiring.
Safety precautions to follow before and during device commissioning.
Step-by-step guide for bringing the device into operation.
Critical safety measures for operating the device correctly.
Covers configurable parameters like language, units, K-factor, outputs, and alarms.
Critical safety measures for performing maintenance tasks.
Guides users through resolving issues based on LED status, error messages, and warnings.
General| Brand | Burkert |
|---|---|
| Model | SE35 |
| Category | Controller |
| Language | English |
To Next Page
