What to do if my Bürkert Transmitter shows 'PWR FAIL'?
If the Bürkert Transmitter displays 'PWR FAIL', it indicates that the supply voltage is too low. This could be because the voltage at the device terminals is below 12 V or the impedance of the current measurement loop is too high. To resolve this, adjust the supply voltage to ensure the voltage at the device terminals is between 12 V and 36 V.
What does 'W. BATCH' mean on my Burkert SE35?
If the device state LED on your Burkert Controller is orange and displays the message 'W. BATCH', it means the number of completed dosings has reached the value specified in the 'BATCH-W.' parameter of the Test menu. To address this, perform the planned maintenance operation and reset the daily totalizer of the completed dosings.
Why is the displayed flow rate always nil on my Bürkert Measuring Instruments?
If the displayed flow rate on your Bürkert Measuring Instruments is always nil, ensure the flow rate in the pipe is not nil, check that the entered K factor is correct. Also, consider choosing a smaller flow rate unit or increasing the number of displayed decimals.
What does 'ERROR3' mean on my Burkert SE35 Controller and how do I fix it?
If the device state LED on your Burkert Controller is red with the message 'ERROR3', it signifies that the user parameters have been lost. Try restarting the device. If the message persists, reconfigure the device.
What does 'CONTINUE' mean on my Burkert SE35?
If the device state LED on your Burkert Controller is any colour and displays the message 'CONTINUE', it indicates that the power supply was interrupted during a dosing, causing the dosing to be interrupted. Check the electrical installation. You can either abort the current dosing or continue it, but in the latter case, verify that the current dosing is accurate.
Why is the displayed quantity increasing slowly on my Burkert SE35 Controller during dosing?
If, during a dosing process, the displayed quantity on your Burkert Controller increases or decreases very slowly and the device state LED is green, check that the K-factor corresponds to the fitting used. You may also perform a Teach-In procedure to determine the K-factor of the fitting used and check that the flow rate in the pipe is high enough.
What does 'Process level' mean on my Burkert SE35?
If your Burkert Controller's device state LED displays any colour with the message 'Process level', it indicates that the power supply was cut during the consultation of the messages of the Information menu via the digital inputs. Ensure that the PLC recognizes that the device has returned to the Process level.
What does 'ERROR4' mean on Bürkert Measuring Instruments and how to fix it?
If your Bürkert Measuring Instruments displays 'ERROR4', it means the totalizer values are lost, and the values saved upon the next to last power down are retrieved. Try restarting the device.
What does 'ERROR3' mean on Bürkert Measuring Instruments and how to fix it?
If your Bürkert Measuring Instruments displays 'ERROR3', it means the user settings are lost, and the device might measure incorrect values. Try restarting the device. If the message continues, reconfigure the device.
What does "MEAS. OVF" mean on Bürkert Measuring Instruments and how to fix it?
If the Bürkert Measuring Instruments shows 'MEAS. OVF', the rotational frequency of the paddle wheel is higher than 250 Hz. Check and adjust the flow rate in the pipe if necessary.
Lists environmental, electrical, and fluid specifications for the compact model.
Lists environmental, electrical, and fluid specifications for the panel model.
Lists environmental, electrical, and fluid specifications for the wall-mounted model.
Lists environmental, electrical, and fluid specifications for the SE35 Batch.
Lists environmental, electrical, and fluid specifications for the 8035 Batch.
Lists technical specs for SE35 Batch with specific sensor-fittings.
Crucial safety guidelines for the fluid installation process.
Step-by-step instructions for installing the 8025 Batch in its compact form.
Step-by-step instructions for installing the 8035 Batch.
Critical safety measures for electrical connections and wiring.
Safety precautions to follow before and during device commissioning.
Step-by-step guide for bringing the device into operation.
Critical safety measures for operating the device correctly.
Covers configurable parameters like language, units, K-factor, outputs, and alarms.
Critical safety measures for performing maintenance tasks.
Guides users through resolving issues based on LED status, error messages, and warnings.
General| Brand | Burkert |
|---|---|
| Model | SE35 |
| Category | Controller |
| Language | English |
To Next Page
