BURNiT Pell Easy series - Page 9

9
TECHNICAL PASSPORT. INSTALLATION and OPERATION MANUAL
TECHNICAL PASSPORT. INSTALLATION and OPERATION MANUAL
EN ISO 17225-2:2014.
The opmal density of the pellets which
guarantees their quality is 605-700 kg per
cubic meter.
Pellet moisture content must not exceed
10%. Make sure you store your fuel in a
dry and well-venlated place.
Table 3. European Cercaon of Wood Pellets for Heang Purposes
Parameters Units ENplus-A1 ENplus-A2 EN-B
Diameter
mm
6 (± 1)
8 (± 1)
6 (± 1)
8 (± 1)
6 (± 1)
8 (± 1)
Length
mm 15 ≤ L ≤ 40
1)
15 ≤ L ≤ 40
1)
15 ≤ L ≤
40
1)
Bulk density
kg / m
2
≥ 600 ≥ 600 ≥ 600
Caloric/heang value
MJ / kg ≥ 16,5-19 ≥ 16,3-19
≥ 16,0-
19
Humidity /moisture
Ма .-% ≤ 10 ≤ 10 ≤ 10
Dust
Ма .-% ≤ 1
3)
≤ 1
3)
≤ 1
3)
Mechanical durability
Ма .-% ≥ 97,5
4)
≥ 97,5
4)
≥ 96,5
4)
Ash
Ма .-%
2)
≤ 0,7 ≤ 1,5 ≤ 3,5
Melng point of ash
°C ≥ 1200 ≥ 1100 -
Chlorine content
Ма .-%
2)
≤ 0,02 ≤ 0,02 ≤ 0,03
Sulfur content
Ма .-%
2)
≤ 0,03 ≤ 0,03 ≤ 0,04
Nitrogen content
Ма .-%
2)
≤ 0,3 ≤ 0,3 ≤ 1,0
Copper content
mg / kg
2)
≤ 10 ≤ 10 ≤ 10
Chromium content
mg / kg
2)
≤ 10 ≤ 10 ≤ 10
Arsenic content
mg / kg
2)
≤ 1,0 ≤ 1,0 ≤ 1,0
Cadmium content
mg / kg
2)
≤ 0,5 ≤ 0,5 ≤ 0,5
Mercury content
mg / kg
2)
≤ 0,1 ≤ 0,1 ≤ 0,1
Lead content
mg / kg
2)
≤ 10 ≤ 10 ≤ 10
Nickel content
mg / kg
2)
≤ 10 ≤ 10 ≤ 10
Zinc content
mg / kg
2)
≤ 100 ≤ 100 ≤ 100
The opmal pellet ash content is ≤ 1%.
This also provides for less frequent
cleaning intervals for the burner.
The table below contains the parameters
which we recommend that you take into
consideraon when choosing fuel for your
Pell burner.
1)
not more than 1% of the pellets may be longer than 40 mm, max. length 45 mm;
2)
dry weight;
3)
parcles <3.15 mm, parculate maer, before handing over the goods;
4)
measurements with Ligno-Tester limit value ≥ 97,7% by weight.