C.E.C. 530CD - Page 31

ENGLISH
buR SAFE AND EFFICIENT
OPERATION
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
@ This equipment ts a sophisticated electromechanical
device. To ensure proper operation, please read this
manual carefully.
Choose the installation location of your unit carefully.
Avoid placing it in direct sunlight. Also avoid locations
Subject to vibration and excessive dust, heat, cold or
moisture. Keep away from such sources of hum as
transformers or motors
Do not use this player where there are extremes in
temperature (below 41°F/5°C or exceeding 95°F:
35°C) or where direct sunlight may strike it.
Do not open the cabinet as this might result in damage
to the set or electrical shock.
Be sure hands are clean when handling discs. Never
insert a disc which has a crack on its surface
When disconnecting the power cord from the wall
outlet, always grasp it by the plug. Never yank the cord.
correct the interference by one or more of the following
measures:
a) Reorient the receiving antenna.
b) Relocate the disc player with respect to the receiver.
Cc) Move the disc player away from the receiver
d) Plug the disc player into a different outlet so that it
is not on the same circuit as the receiver.
If necessary, the user should consult the dealer or an
experienced radio ‘television technician for additional
suggestions
BEFORE USE (Fig. 1)
To protect the internal laser pickup mechanism from
shocks and movement during transit, it has been secured by
special transport screws and a fixing screw. The positions of
these screws are indicated on the player's bottom panel.
Using a screwdriver, remove the three transport screws
and turn the fixing screw fully counterclockwise (as indi-
cated by the arrow), before the player is switched on.
(Keep the transport screws for the later use.)
* “ §ot use force when operating the switch and buttons.
ore moving the set be sure to disconnect the
power Cord and all connecting cables.
To keep the laser-pickup clean, do not forget to close
the disc tray.
Do not attempt to clean the unit with chemical solvents
as this might damage the finish. Use a clean, dry cloth.
DANGER:
When the enclosure is removed and the safety
interlock is defeated or has failed, avoid direct
exposure to invisible laser beam.
Be sure to read the TROUBLESHOOTING GUIDE section
for advice on common operating errors before conclud-
ing that your unit requires service.
Keep this manual in a safe place for future reference.
This digital compact disc player generates and uses
radio frequency energy and if not installed and used
properly, that is, in strict accordance with the
manufacturer's instructions, it may interfere with
radio and television reception. It is designed to provide
reasonable protection against such interference in a
residential installation’. However, there is no guarantee
that interference will not occur in a particular installa-
tion. If the unit does interfere with radio or television
reception, which can be determined by switching the
disc player on and off, the user is encouraged to try to
Fixing Screw
BEFORE TRANSPORTING THE UNIT
If the player is to be transported for long distances, the
transport screws should be reinstalled and the fixing
screw should be secured.
Before installing the screws, open the disc tray to make
sure that there is no disc in it, then close the tray again.
After approximately 3 seconds have elapsed, switch off
—-|l-
the player. Using a screwdriver, turn the fixing screw
clockwise against the arrow to fix the pickup mechanism
and install the three transport screws.
IMPORTANT... This Digital Compact Disc Player was
developed to give you many years of enjoyment. Please
read the following instructions carefully. They have been
prepared to assist you during the initial set-up procedure
and to assure you of optimum performance at all times.
THE WARRANTY ON THIS UNIT DOES NOT COVER
DAMAGE CAUSED BY MISHANOLING OR MISUSE.
CONNECTING THE DIGITAL
COMPACT DISC PLAYER
CAUTION:
© Before connecting the unit to your audio system,
make sure that the 3 transport screws have been
removed and the fixing screw has been turned fully
counterclockwise.
© Before making connections or disconnections, be
sure to switch off the power to each component.
© Be sure to make the correct connections, paying
attention to the L (left channel) and R (right channel)
marks. Plug in the cables securely. Loose connections
will result in unsatisfactory sound reproduction or
Cause noise problems. Refer to Fig. 2.
@ After all connections have been completed, connect
the power cord of the main unit to either a household
outlet or an auxiliary outlet on the amplifier.
@ If this unit interferes with the tuner, switch off the unit
during tuner operation.
@ LINE OUT Jacks...
Connect one end of the patch cords (supplied) to the
player's OUTPUT jacks and the other end to the jacks
designated by CD, DAD, AUX, TAPE PLAY, T.V.,
TUNER, etc., on the amplifier. Do not connect it to
the amplifier’s PHONO jacks.
Do not confuse the right (R) and left (L) cords when
making connections. The white plug is for the !eft
channel and the red plug is for the right channel.
@ AC Power Cord...
After completing the installation and all connections,
make sure that the POWER switch on the front panel
of the player is set to OFF. Then plug the power cord
into an AC wall outlet.
i err ee