Calpeda e-idos META - User Manual

Questions and Answers

J
Jenna LeeAug 2, 2025
What to do if my Calpeda e-idos META motor does not start?
- S
  Stacey BeckAug 2, 2025
  First, verify that the mains frequency and voltage match the electrical characteristics on the indicator plate. If the power supply is suitable, check for any blockage of the shaft and remove it according to the instructions in the “Blocked pump” instruction booklet. If the issue persists after checking these causes, the engine may be malfunctioning and should be repaired or replaced by an authorised service centre.
C
campbelldeannaAug 6, 2025
Why is there insufficient flow from my Calpeda e-idos META?
- T
  tsimsAug 7, 2025
  Several factors can cause insufficient flow. Ensure that the pipes and accessories used are suitable for the application to avoid excessive head loss. Check for deposits or solid bodies in the rotor's internal passages; clean the rotor and install a suction filter. Other possible causes include a deteriorated or worn rotor and pump case, excessive liquid viscosity, excessive suction head, or a suction pipe that is too long. If the liquid's viscosity is too high, the pump is unsuitable. Try closing the feeder gate partially or reducing the level difference if the suction head is excessive. For long suction pipes, move the pump closer to the suction tank or use a wider pipe.
L
Lauren GrahamAug 11, 2025
What to do if my Calpeda e-idos META Water Pump is blocked?
- L
  lawsonmorganAug 11, 2025
  If your pump is blocked, it could be due to rust from prolonged inactivity. Try unblocking it by using a screwdriver to turn the notch on the back of the shaft, but remember to turn off the electricity supply first. Alternatively, the blockage may be due to solid objects in the pump rotor. If possible, dismantle the pump casing and remove any foreign bodies. If the bearings are seized, replace them.
A
anitajonesAug 15, 2025
Why is my Calpeda e-idos META so noisy and vibrating?
- O
  owhitakerAug 15, 2025
  Noise and vibrations can stem from several issues. Check if any solid objects are obstructing the rotor. Other causes include worn bearings (replace them), loose pump and pipes (anchor them firmly), flow too strong for the delivery pipe's diameter (use bigger diameters or reduce flow), functioning in cavitation (reduce flow by adjusting the feeder gate or using bigger pipes), or an unbalanced power supply (check the mains voltage).
C
Cameron WardAug 19, 2025
What to do if my Calpeda e-idos META does not stop?
- J
  jeffrey47Aug 19, 2025
  If your pump won't stop, the non-return valve may be broken, blocked, or clogged with solid parts; check and remove any obstructions. Also, the stop pressure (parameter UP01) might be too high; check and reduce it if necessary. Check the membrane pressure, if necessary install a tank of at least 8 liters.
S
Samantha ShepherdAug 23, 2025
What to do if my Calpeda Water Pump functions but no water comes out?
- K
  Kaylee StrongAug 23, 2025
  If the pump runs but no water is coming out, there might be an air infiltration from suction tube connections, drain plugs, the filling of pump, or the gaskets of the suction pipe; check and seal any leaks. The foot valve could be blocked, or the suction pipe might not be fully immersed in liquid; clean or replace the bottom valve and ensure the suction pipe is suitable. Another cause may be a blocked suction filter; clean or replace it. Verify that the integrated non-return valve is working properly.
K
Krystal RamirezAug 28, 2025
What causes leakage from the mechanical seal in my Calpeda Water Pump?
- R
  ritazamoraAug 28, 2025
  Leakage from the mechanical seal can occur if the seal has functioned when dry or has stuck. It may also be scored by abrasive parts in the liquid pumped. Ensure the pump casing and suction pipe are full of liquid and air has been expelled. A slight initial drip during filling or start-up may occur as the seal adjusts; wait to see if it stops. Also, the mechanical seal may be unsuitable for the application. Install a suction filter and use a seal suited to the characteristics of the liquid being pumped.

Summary

General Information

Symbols and Warnings

Explains symbols used for understanding and safety.

Manufacturer Information

Provides manufacturer's name, address, and website for contact.

Authorized Operators

Defines who is authorized to use and maintain the product.

Warranty Information

Outlines what the product warranty covers and its limitations.

Technical Assistance

Details how to request further information, technical support, and spare parts.

Technical Description

Intended Use

Specifies the intended applications and liquid types for the device.

Improper Use

Warns against using the device for purposes other than those specified.

Product Marking

Describes the information found on the pump's name-plate.

Technical Features

Technical Data

Lists key technical specifications like speed, voltage, pressure, and sound levels.

Pushbutton Functions

Explains the specific functions of each pushbutton on the user interface.

Safety

General Safety Provisions

General safety rules and precautions to be followed before using the product.

Safety Devices

Describes the external case that protects against contact with internal parts.

Residual Risks

States that the device has no residual risks when used according to rules.

Information and Safety Signals

Notes that there are no specific signals on the product itself.

Individual Protection Devices

Recommends using personal protective equipment during operations.

Transportation and Handling

Handling Precautions

Provides instructions for careful handling to prevent damage during transport.

Installation

Dimensions

Refers to the technical catalogue for device dimensions.

Ambient Requirements and Installation Site

Details environmental conditions and site requirements for installation.

Unpacking

Instructions for inspecting the device for damages after unpacking.

Installation Guidelines

General guidelines for installing the pump and its components.

Pipes and Connections

Advises on pipe cleanliness, securing, and diameter for proper connection.

Suction Pipe Installation

Specific instructions for installing the suction pipe to avoid air pockets.

Programming Guide

Electrical Connection

Instructions for safe electrical connection by a qualified electrician.

Operation with Frequency Converter

Warning against using the pump with a frequency converter.

Parameters Overview

Lists the types of information displayed during operation and programming.

Pump Status Parameters

Details parameters that allow visualization of pump status and readings.

Programming Parameters

Explains how to access and view user and advanced programming parameters.

Available Parameters

Lists and describes the user (UP) and advanced (AP) parameters.

User Settings (UP Parameters)

Details user-configurable parameters like set-point pressure and dry-run modes.

Advanced Settings (AP Parameters)

Lists advanced parameters requiring a password, intended for qualified personnel.

Operating Modes

Describes how the system maintains constant pressure and its expansion vessel function.

Startup and Operation

Warning for High Number of Starts;Hour

Explains the TANK symbol warning for frequent pump starts.

Dry-Run Settings and Management

Details how the pump behaves and recovers from dry-run conditions.

Forced Start Function

Describes the automatic pump start to prevent mechanical blocks after inactivity.

Forced Stop Function

Explains the timer function to stop the pump under low power consumption.

Safe-Start Function

How to enable and what the safe-start function does to prevent pressure peaks.

Password Insertion

Instructions on how to enter the password to access protected menus.

Preliminary Checks Before Start-up

Essential checks to perform before starting the pump.

Startup Parameters

Notes that the pump is pre-set with operating parameters.

Suction Pressure Set-up

How to set the suction pressure parameter (AP01) and its implications.

First Starting Procedure

Detailed steps for the initial start-up, including priming and filling.

Self-Priming Capability

Conditions and procedures for the pump's self-priming function.

Maintenance

Vessel Pressure Adjustment

Instructions for adjusting the preloaded pressure of the tank.

Gate Valve Regulation

How to regulate the delivery gate valve to reduce noise.

Abnormal Operation Warnings

Warnings about running the pump with a closed gate valve or overheating.

Switch Off Procedure

How to safely switch off the appliance by disconnecting the power supply.

Routine Maintenance

General precautions before performing maintenance and specific tasks.

Disposal

Vessel Maintenance

Instructions for inspecting the preloaded pressure of the membrane in the pump.

Dismantling the System

Steps to close valves and drain the pump before dismantling.

Dismantling the Pump

Instructions to close valves and drain the pump casing before dismantling.

Disposal Procedure

Guidelines for the final disposal of the device according to regulations.

Spare Parts

Spare Parts Request

Information on how to order spare parts, including required details.

Designation of Parts

Lists parts with their designation numbers for identification and ordering.

Alarms

Alarm Codes and Reset Procedures

Lists error codes, their descriptions, reset types, and causes.

Warnings

Warning Status

Explains the warning status and its relation to error status.

Warning Codes and Possible Remedies

Lists warning codes, their causes, and suggested remedies.

Troubleshooting

Troubleshooting Guide

A table listing common problems, their probable causes, and possible remedies.

Installation Examples

Positive Suction Head Operation Example

Illustrates a typical installation for positive suction head operation.

Suction Lift Operation Example

Illustrates a typical installation for suction lift operation.

Pipeline Supports and Clamps Example

Shows how to properly support and clamp pipelines.

Filling Procedure Example

Demonstrates the procedure for filling the pump.

Draining Procedure Example

Demonstrates the procedure for draining the pump.

Dismantling and Assembly Drawing

Exploded view drawing showing all parts for dismantling and assembly.

Calpeda e-idos META Specifications

General

Liquid Temperature Range	0°C to +40°C
Maximum Operating Pressure	8 bar
Protection Degree	IP44
Insulation Class	F
Single Phase Power Supply	Yes
Pumped Liquid	Clean Water
Power	0.37 kW to 1.5 kW
Voltage	230V
Frequency	50 Hz
Inlet/Outlet Size	1 inch
Max Pressure	8 bar
Housing Material	Cast Iron
Motor Type	Asynchronous
Application	Water Supply, Pressure Boosting, Irrigation
Installation	Horizontal or vertical
Max Flow Rate	7.2 m³/h
Impeller Material	Technopolymer
Seal Material	Ceramic/Graphite
Type	Centrifugal pump