Calpeda NM User Manual (English)

Other manuals for Calpeda NM

Questions and Answers:

M
Melissa OchoaAug 17, 2025
Why is my Calpeda NM making noise and vibrations?
- W
  wiseomarAug 17, 2025
  If your Calpeda Water Pump is making unusual noises and vibrations, start by checking if any solid objects are stuck in the rotor. Also, inspect the bearings for wear and tear, and replace them if needed. Ensure the pump and pipes are securely attached. The flow might be too strong for the delivery pipe's diameter; consider using larger pipes or reducing the pump flow. Functioning in cavitation can also cause this issue; adjust the feeder gate, use pipes with a bigger internal diameter, and check if the suction head is excessive. Verify the mains voltage is correct and re-align the pump-motor unit if necessary.
T
toddhowellAug 20, 2025
Why is the flow insufficient in my Calpeda NM?
- D
  Diana MartinAug 20, 2025
  If your Calpeda Water Pump isn't providing sufficient flow, it could be due to several reasons. Check if the pipes and accessories have a diameter too small, causing excessive head loss; use pipes and accessories suitable for the specific application. Inspect the rotor for deposits or solid bodies in the internal passages; clean the rotor and install a suction filter. If the rotor is deteriorated or worn, replace it and the pump casing. Ensure the liquid's viscosity isn't too high and the pump is suitable for it. Verify the direction of rotation is correct by inverting the electrical connections. Reduce the suction head if it's excessive and shorten the suction pipe or use a wider diameter pipe.
T
Thomas HowardAug 22, 2025
How to troubleshoot a Calpeda NM Water Pump that does not start?
- D
  Dr. Jennifer Mason MDAug 22, 2025
  If your Calpeda Water Pump motor isn't starting, begin by verifying that the mains frequency and voltage match the electrical characteristics on the indicator plate. Ensure the power supply cable is correctly connected to the terminal board and that the thermal overload protection is properly set. If the engine overload protective device has activated, check the power supply and ensure the pump shaft turns freely. Also, see that the fuses are not blown or defective; replace them if necessary and re-check the electrical power supply.
A
amanda57Aug 26, 2025
What to do if my Calpeda NM functions but no water comes out?
- T
  tammymillsAug 26, 2025
  If your Calpeda Water Pump functions but no water comes out, check for air infiltration from suction tube connections, drain plugs, or gaskets; seal any loose connections. Ensure the foot valve isn't blocked and the suction pipe is fully immersed in liquid; clean or replace the bottom valve and use a suitable suction pipe. Also, inspect the suction filter for blockages; clean or replace it if necessary.
J
Jennifer UnderwoodAug 28, 2025
How to unblock a Calpeda Water Pump?
- A
  Andre MarksAug 28, 2025
  If your Calpeda Water Pump is blocked, it could be due to rust formation from prolonged inactivity. Try to start rotation directly from the pump shaft or joint, remembering to turn off the electricity supply first. Solid bodies in the pump rotor can also cause blockage; dismantle the pump casing to remove any foreign objects. Alternatively, seized bearings can be the problem; replace them if damaged.
Z
Zachary GarciaAug 31, 2025
Why is my Calpeda Water Pump leaking from the mechanical seal?
- A
  Andrea PhelpsAug 31, 2025
  If your Calpeda Water Pump is leaking from the mechanical seal, it may be because the seal has functioned when dry or has stuck. It could also be scored by abrasive parts in the liquid. Also, the mechanical seal may be unsuitable for the application. In such cases, replace the seal. However, a slight initial drip during filling or first start-up is normal; wait for the seal to adjust. If the problem persists, consider replacing the seal or contacting an authorized service center.
A
amy00Sep 2, 2025
Why Calpeda Water Pump engine does not start?
- B
  Brian GonzalezSep 2, 2025
  If your Calpeda Water Pump engine isn't starting, several factors could be at play. First, confirm that the mains frequency and voltage are appropriate. Next, ensure the power supply cable is correctly connected and that the thermal overload protection is properly set. Also, verify that the pump shaft turns freely and that the thermal overload protection isn't causing the issue. Finally, check for blown or defective fuses, and if found, replace them, re-examining the power supply and shaft movement.
M
Maria CohenSep 5, 2025
How to increase flow in Calpeda Water Pump?
- V
  Valerie AyalaSep 5, 2025
  If your Calpeda Water Pump isn't delivering enough flow, several factors could be responsible. Ensure that the pipes and accessories you're using are appropriately sized for the application. Clean the impeller to remove any deposits or solid bodies, and consider installing a suction filter. If the rotor is deteriorated or worn, along with the pump case, replacement is necessary. For water with dissolved gases, use the feeder gate to perform opening and closing maneuvers. If the liquid's viscosity is too high, the pump may be unsuitable. Finally, check and correct the direction of rotation by inverting the electrical connections on the terminal board.
L
Lindsey BraySep 8, 2025
Why is my Calpeda Water Pump making noise and vibrating?
- C
  Christopher BarrySep 8, 2025
  If your Calpeda Water Pump is making unusual noises or vibrating, worn bearings could be the cause, requiring replacement. Another potential reason is an unbalanced power supply, so it's important to verify that the mains voltage is correct.
I
ihallSep 12, 2025
What to do if my Calpeda Water Pump is blocked?
- R
  Ricky JonesSep 12, 2025
  If your Calpeda Water Pump is blocked, it could be due to a few reasons. If the pump hasn't been used for a while, try unblocking it by using a screwdriver to turn the notch on the back of the shaft. Also, check for any solid objects in the impeller and remove them. In some cases, the bearings might be blocked, which would mean they need to be replaced.

Calpeda NM Specifications

General

Temperature Range	-10°C to +90°C
Connection Type	Flanged
Maximum Working Pressure	10 bar
Pump Type	Centrifugal
Application	Water supply
Voltage	230V or 400V
Frequency	50Hz