Candy CS 1071DE-88 - User Manual

Questions and Answers

K
Kaitlin WilliamsAug 13, 2025
Why Candy CS 1071DE-88 Washer does not work / start?
- B
  Brian LopezAug 13, 2025
  If your Candy Washer doesn't start, try these steps: First, ensure the washer is properly plugged into a working electrical outlet and that the power is switched on. Test the outlet with another device, like a lamp, to confirm it's functioning. Also, make sure the door is fully closed. Check that you've correctly selected the desired program and pressed the start button. Finally, verify that the washer isn't in pause or time delay mode.
B
Becky LoweAug 16, 2025
What to do if Candy Washer leaks water on the floor?
- E
  Edward HarrisonAug 16, 2025
  If you notice water leaking near your Candy Washer, it could be due to a leak from the seal between the tap, supply hose, and fill valve. In this case, replace the seal and ensure the hose connections are tightened correctly. Also, make sure the front filter is correctly closed.
A
Ashley AndersonAug 20, 2025
What to do if Candy Washer doesn't spin?
- T
  tmorrisonAug 20, 2025
  If your Candy Washer isn't spinning, try these solutions: remove the load, de-tangle it, reload it, and then restart the spin program. Also, make sure the 'no spin' option is not selected. Check the selected options and their impact on the spin cycle. Ensure you're using the correct amount of detergent. If the problem continues, refer to the Error 3 section.
E
Edward McknightAug 25, 2025
Why Candy CS 1071DE-88 makes strong vibrations / noises during spin cycle?
- C
  Carmen HarperAug 25, 2025
  Strong vibrations or noises during the spin cycle of your Candy Washer can be caused by several factors. First, ensure that the transport screws, rubber bungs, and spacer tubes have been removed from the machine. Check the inside of the drum for any foreign objects like coins, hinges or buttons. If necessary, adjust the feet of the washing machine as indicated in the installation section of the manual.
K
Kayla SimmonsAug 27, 2025
What to do if Candy CS 1071DE-88 Washer displays E2 error?
- C
  Cynthia GibsonAug 28, 2025
  If your Candy Washer displays error code E2 or the LEDs flash twice, ensure that the water supply tap is open and the water supply hose isn’t bent, kinked, or trapped. Check that the drain pipe is at the correct height as shown in the installation section. Close the water supply tap, unscrew the filler hose from the back, and check that the anti-sand filter is clean and not blocked. Also, check that the filter is not clogged or that there are no foreign objects inside the filter compartment that can obstruct the proper flow of water.
S
Shannon NicholsonSep 1, 2025
What to do if Candy CS 1071DE-88 Washer displays E3 error?
- M
  Matthew JonesSep 1, 2025
  If your Candy Washer shows error code E3 or the LEDs flash 3 times, check that the filter isn't clogged and that there are no foreign objects blocking water flow inside the filter compartment. Also, ensure the drain hose isn’t bent, kinked, or trapped. Verify that your home drainage system isn't blocked, allowing water to flow freely; try draining water in the sink to test it.
C
christopher59Sep 4, 2025
What to do if Candy CS 1071DE-88 Washer displays E7 error?
- G
  Glenn HowardSep 4, 2025
  If your Candy Washer displays error code E7 or the LEDs flash 7 times, make sure the door is correctly closed and that no clothing is preventing it from fully closing. If the door is locked, switch off and unplug the washing machine, wait 2-3 minutes, and then try reopening the door.
C
Christopher PrestonSep 8, 2025
What to do if Candy Washer displays E4 error?
- B
  Bryan RichardsonSep 8, 2025
  If your Candy Washer displays error code E4 or the LEDs flash 4 times, ensure you are using the correct amount of detergent and that the detergent is designed for use in a washing machine.