Canworld CDE360-4T2R2G/3R7L - User Manual

CDE360 Vector Control AC Drive Preface
Preface
Thank you for purchasing CDE360 Vector Control AC Drive developed by Shenzhen Canworld
Electrical Technology Co., Ltd.
The CDE360 series AC drive is a general-purpose high-performance vector control AC drive, which
is widely used for simple fan and pump driving, and automatic controlling in specific industry
equipment of Textile, Stone sawing machine, Air compressor, Spindle servo drive, Crane, Veneer
peeling machine, line cutting machine, oil-fields and wire drawing machine. It can also provide
all-in-one solution for the application of ball crusher, injection molding machine and intelligent motor.
This manual describes the notes and guidance of selection, installation, parameter setting, field
debugging, fault diagnostics and daily maintenance. Read and understand the user manual before
use and forward the manual to the end user.
Notes
 The drawings in the user manual are sometimes shown without covers or protective guards.
Remember to install the covers and protective guards according to the user manual, then
perform operations in accordance with the instructions.
 The drawings in the manual are shown for description only and may not match the product
that you purchased.
 The instructions are subject to change without notice, due to product upgrade and the
efforts to increase the accuracy and convenience of the user manual.
 Contact our agents or customer service center if you need to purchase this user manual.
 Contact our customer service center if you have problems during the use.
Service hot line: +86 4000-888-699 Fax: +86 755-26617646
Version: V1.1

Summary

Chapter 1 Safety Information and Precautions

Pre-Installation Safety Guidelines

Safety guidelines to follow before installing the AC drive.

Installation Safety Guidelines

Safety guidelines to follow during the installation process.

Wiring Safety Precautions

Safety guidelines related to wiring the AC drive components.

Pre-Power-On Safety Checks

Safety checks to perform before powering on the AC drive.

Post-Power-On Safety Guidelines

Safety guidelines to follow after powering on the AC drive.

During Operation Safety Guidelines

Safety guidelines to follow during AC drive operation.

During Maintenance Safety Guidelines

Safety guidelines to follow during AC drive maintenance.

General Safety Precautions for AC Drive Usage

General safety advice and precautions for AC drive usage.

Chapter 2 Product Information

Selection Suggestion of AC Drive

Guidance for selecting the appropriate AC drive based on application.

Recommendation of Brake Resistance Selection

Recommendations for selecting brake resistance based on AC drive models.

Chapter 3 Mechanical and Electrical Installation

Mechanical Installation Requirements

Requirements for the mechanical installation environment.

Installation Direction and Clearance Guidelines

Guidelines for AC drive installation direction and clearance.

Electrical Installation Overview

General overview of the electrical installation process.

Peripheral Electrical Components Selection Guidance

Guidance on selecting appropriate peripheral electrical components.

AC Drive Terminals Wiring Diagram

Diagram illustrating the wiring of the AC drive terminals.

Power Terminals of the Main Circuit

Description of the AC drive's main circuit power terminals.

Control Terminals and Wiring Description

Description of control terminals and their wiring.

Chapter 4 Operation, Display and Application

Keypad Interface Overview

Overview of the AC drive keypad interface.

Keypad Key Functions Explanation

Explanation of the functions of each key on the AC drive keypad.

Menu Navigation Introduction

Introduction to navigating the AC drive's menu system.

Monitor Parameters Usage

How to use the monitor parameters function of the AC drive.

Parameters Upload and Download Procedures

Procedures for uploading and downloading AC drive parameters.

Password and Parameter Setting

How to set and manage user passwords and parameters.

Chapter 5 Parameter List Table

Group A0: Monitor Parameters

List of parameters for monitoring AC drive status.

Group A1: Fault & Diagnostics Parameters

List of parameters for fault and diagnostic information.

Group b0: Basic Parameters

List of basic parameters for AC drive configuration.

Group C: Input and Output Terminals Parameters

Parameters related to input and output terminals.

Group d: Motor Control Parameters

Parameters for controlling motor operation.

Group E: Expanding Application Functions Parameters

Parameters for expanding application functions.

Group F: Protection and Reset Parameters

Parameters for protection and reset functions.

Group H: System Parameters and Analog Calibration

Parameters for system settings and analog calibration.

Group L: Communication Setting Parameters

Parameters for configuring communication settings.

Group P: User-defined and Debug Parameters

Parameters for user-defined settings and debugging.

A0 Monitor Parameters

Detailed list of monitor parameters for the AC drive.

A1 Fault & Diagnostics Parameters

Detailed list of fault and diagnostic parameters.

b0 Basic Parameters

Detailed list of basic parameters for AC drive configuration.

b1 Run & Stop Logic Parameters

Parameters defining the run and stop logic of the AC drive.

b2 Frequency Source Parameters

Parameters for selecting the AC drive's frequency source.

C0 Digital Input Parameters

Parameters related to the AC drive's digital input terminals.

C1 Digital Output Parameters

Parameters related to the AC drive's digital output terminals.

C2 Analog Input Parameters

Parameters related to the AC drive's analog input terminals.

C3 Analog Output Parameters

Parameters related to the AC drive's analog output terminals.

C4 Pulse Input;Output Parameters

Parameters for pulse input and output functions.

C5 Virtual Digital Input;Output Parameters

d0 Motor Control Parameters

d1 Motor Parameters

d2 Speed Control Parameters

d3 Torque Control Parameters

d5 Motor 2 Parameters

d6 Motor 2 Speed Control Parameters

E0 JOG Parameters

E1 Skip Frequency Parameters

E2 Multi-Reference Parameters

E3 Simple PLC Parameters

E4 Acceleration & Deceleration Time Parameters

E5 PID Parameters

E6 Multi-Pump Control Parameters

E7 Swing Frequency Parameters

E8 Droop Control Parameters

E9 Power Loss Ride Through Parameters

Eb Supervision Parameters

F0 Protection Parameters

F1 Auto Reset Parameters

H0 System Parameters

H1 AI;AO Calibration Parameters

L0 Communication Setting Parameters

L1 Point-point Communication Parameters

L2 Encoder Setting Parameters

P0 User-defined Parameters

Chapter 6 Parameters Description

Group A0: Monitor Parameters Description

Group A1: Fault & Diagnostics Parameters Description

Group b0: Basic Parameters Description

Group b1: Run & Stop Logic Parameters Description

Group b2: Frequency Source Parameters Description

Group C0: Digital Input Parameters Description

Group C1: Digital Output Parameters Description

Group C2: Analog Input Parameters Description

Group C3: Analog Output Parameters Description

Group C4: Pulse Input;Output Parameters Description

Group C5: Virtual Digital Input;Output Parameters Description

Group d0: Motor Control Parameters Description

Group d1: Motor Parameters Description

Group d2: Speed Control Parameters Description

Group d3: Torque Control Parameters Description

Group d5: Motor 2 Parameters Description

Group d6: Motor 2 Speed Control Parameters Description

Group E0: JOG Parameters Description

Group E1: Skip Frequency Parameters Description

Group E2: Multi-Reference Parameters Description

Group E3: Simple PLC Parameters Description

Group E4: Acc & Dec Time Parameters Description

Group E5: PID Parameters Description

E5 PID Parameters Description

Group E6: Multi-Pump Control Parameters Description

Group E7: Swing Frequency Parameters Description

Group E8: Droop Control Parameters Description

Group E9: Power Loss Ride Through Parameters Description

Group EA: External Brake Parameters Description

Group Eb: Supervision Parameters Description

Group F0: Protection Parameters Description

Group F1: Auto Reset Parameters Description

Group H0: System Parameters Description

Group H1: AI;AO Calibration Parameters Description

Group L0: Communication Setting Parameters Description

Group L1: Point-point Communication Parameters Description

Group L2: Encoder Setting Parameters Description

Group P0: User-defined Parameters Description

Chapter 7 Fault Detection and Diagnostics

Faults and Solutions Overview

Common faults and their corresponding solutions for troubleshooting.

Common Faults and Solutions Analysis

Common faults and their corresponding solutions for simple analysis.

Chapter 8 Communication Protocol

Protocol Comments and Basics

RTU Protocol Format

MODBUS Protocol Functions

AC Drive Fault Description (Read-only)

Chapter 9 Maintenance

Routine Repair and Maintenance Procedures

Routine procedures for AC drive repair and maintenance.

Inspection and Replacement of Vulnerable Components

Chapter 10 Optional Cards

Canworld CDE360-4T2R2G/3R7L Specifications

General

Model	CDE360-4T2R2G/3R7L
Category	DC Drives
Control Method	Vector Control
Cooling Method	Air cooling
Protection Features	Overvoltage, Undervoltage, Short Circuit