Carrier 42HQE018 - Remote Controller; Use of the Remote Control

GB - 8
42HQE009 / 012 / 018 / 022
Remote controller
A
U
T
O
C
O
O
L
D
R
Y
H
E
A
T
F
A
N
T
E
M
P
C
L
O
C
K
TIM
ER ON
TIMER OFF
SPEED
A
U
T
O
L
O
W
M
E
D
H
IG
H
M
O
D
E
O
N
OFF
T
E
M
P
F
A
N
S
PE
E
D
A
IR
D
IRE
CT
IO
N
SW
IN
G
C
LO
C
K
E
CO
N
O
M
IC
R
U
NN
IN
G
T
IM
E
R
O
N
TIM
E
R
O
F
F
TIME ADJUST
O
K
C
A
N
C
E
L
8m
T
E
M
P
C
L
O
C
K
SP
E
ED
M
O
D
E
F
A
N
S
P
E
E
D
ON
O
FF
TEMP
C
AUTO COOL DRY HEAT FAN
TEMP
CLOCK
TIMER ON
TIMER OFF
SPEED
AUTO LOW MED HIGH
MODE
ON
OFF
TEMP
FAN
SPEED
AIR
DIRECTION
SWING
CLOCK
ECONOMIC
RUNNING
TIMER ON
TIMER OFF
TIME ADJUST
OK
CANCEL
Clock
Handling the remote controller
Location of the remote controller.
• Keep the remote controller where its signals can reach the
receiver of the indoor unit. (a distance of 8m is allowed).
• When you select the timer operation, the remote controller
automatically transmits a signal to the indoor unit at the specified
time. If you keep the remote controller in a position that
hinders proper signal transmission, a time lag of up to 15
minutes may occur.
CAUTIONS
• The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor
unit.
• Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is exposed to
direct sunlight, the air conditioner may not function properly. Use
curtains to prevent the sunlight from falling on the receiver.
• If other electrical appliances react to the remote controller, either
move these appliancesor consult your local dealer.
Replacing batteries
The remote controller uses two alkaline dry batteries (R03/LR03X2)
1. Slide the cover of the battery compartment, then replace the
old batteries with new ones.
2. After step 1 is done, push the RESET button.
3. Before replacing the battery compartment cover, confirm that the
display screen on the remote controller displays "0:00" and that
the colon is flashing.
• After replacing batteries, set the remote controller clock.
NOTES
- When replacing batteries, do not use old batteries or different type
batteries. Otherwise it may cause the remote controller to
malfunction.
- If you do not use the remote controller for more a few weeks,remove
the batteries.
Otherwise, battery leakage may damage the remote controller.
- The average battery life during normal use is approximately half a
year.
- Replace the batteries when there is no receiving beep from the
indoor unit or if the transmission indicator on the remote controller
fails to light.
Use of the remote control
Setting the clock
Before you start operating the air conditioner, set the clock of the
remote controller using the procedures given in this section.
The clock panel on the remote controller will display the time
regardless of whether the air conditioner is in use or not.
Initial Setting or the Clock
When batteries are inserted in the remote controller, the clock panel
will display "0:00" and the colon will flash.
 Time adjust button (TIME ADJUST)
• push this button to set time.
Forward.
Backward.
• Each time you push the button, the time moves forward or
backward by one minute depending on which side you Push.
The time alters as quickly as you push the button.
 OK button
When you push the OK
button, the clock time display
stops flashing and the clock
starts operating.
 Readjusting the Clock
Push the CLOCK button in
the battery compartment,
the colon in the clock display will start to flash.
To set the new time, follow 1 and 2 of "Initial Setting of the Clock".
* Clock accuracy is within 10 seconds per day.
CAUTIONS
Static electricity or other factors (in case of extremely high voltage)
can cause remote controller clock initialise. If your remote controller
is initialized (flashing of the colon in "0:00"), readjust the clock
before you start operation.


