AQUASNAP ®
30RB060-390
Air-Cooled Chillers
60 Hz
Installation Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS ...................... l
INTRODUCTION ............................... 1-23
INSTALLATION ............................... 24-54
Storage ......................................... 24
Step 1 -- Rig and Place the Unit ................. 24
• PLACING UNIT
• MOUNTING UNIT
• RIGGING UNIT
Step 2 -- Remove Compressor Rack Holddown
Bolts ............................................ 24
Step 3 -- Cooler Fluid and Drain Piping
Connections .................................. 28
• FREEZE PROTECTION
• UNITS WITH HYDRONIC PUMP PACKAGE
• UNITS WITHOUT HYDRONIC PUMP PACKAGE
• FOR ALL UNITS
Step 4 -- Fill the Chilled Water Loop ............ 32
WATER SYSTEM CLEANING
WATER TREATMENT
SYSTEM PRESSURIZATION
FILLING THE SYSTEM
SET WATER FLOW RATE
PUMP MODIFICATION/TRIMMING
PREPARATION FOR YEAR-ROUND
OPERATION
• FREEZE PROTECTION
• PREPARATION FOR WINTER SHUTDOWN
Step 5 -- Make Electrical Connections .......... 42
POWER SUPPLY
POWER WIRING
CONTROL POWER
FIELD CONTROL OPTION WIRING
DUAL CHILLER LEAVING WATER SENSOR
CARRIER COMFORT NETWORK,_R)COMMUNICA-
TION BUS WIRING
• NON-CCN COMMUNICATION WIRING
Step 6 -- Install Accessories .................... 54
• NAVIGATOR TM DISPLAY
REMOTE ENHANCED DISPLAY
LOW AMBIENT TEMPERATURE OPERATION
MINIMUM LOAD ACCESSORY
UNIT SECURITY/PROTECTION ACCESSORIES
COMMUNICATION ACCESSORIES
SERVICE OPTIONS
Step 7 -- Refrigerant Circuit ..................... 54
• LEAK TESTING
• DEHYDRATION
• REFRIGERANT CHARGE
SAFETY CONSIDERATIONS
Installing, starting up, and servicing air-conditioning
equipment can be hazardous due to system pressures, electrical
colnponents, and equipment location.
Only trained, qualified installers and service mechanics
should install, start up, and service this equipment.
Untrained personnel can perform basic maintenance func-
tions such as cleaning coils. All other operations should be
performed by trained service personnel.
When working on the equipment, observe precautions in the
literature and on tags, stickers, and labels attached to the
equipment.
• Follow all safety codes.
• Keep quenching cloth and fire extinguisher nearby when
brazing.
• Wear safety glasses and work gloves.
• Use care in handling, rigging, and setting bulky
equipment.
Electrical shock can cause personal injury and death. Shut
off all power to this equipment during installation. There
may be more than one disconnect switch. Tag all discon-
nect locations to alert others not to restore power until work
is completed.
IMPORTANT: This equipment generates, uses, and can
radiate radio tiequency eneILWand if not installed and
used in accordance with these instructions may cause
radio interference. It has been tested and found to comply
with the limits of a Class A computing device as defined
by FCC (Federal Comlnunlcations Colrnnission, U.S.A.)
regulations, Subpart J of Part 15, which are desimled to
provide reasonable protection against such interference
when operated in a colrnnercial enviropanent.
This system uses Puron,_r9R-410a refi-igerant, which has
hi_ler pressures than R-22 aald other refrigerants. No other
refi-igerant can be used in this system. Failure to use gage
set, hoses, and recovery systems desimned to handle Puron
R-410a refi-igerant may result in equipment damage oi per-
sonal injury. If un8ure about equipment, consult the equip-
ment manufacmrer.
INTRODUCTION
These instructions cover installation of 30RB060-390 air-
cooled liquid chillers with electronic controls and units with
thctory-installed options (FIOPs). See Fig. 1.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300001-01 Printed in U.S.A. Form 30RB-SSI Pg 1 8-06 Replaces: 30RB-1SI
To Next Page
Need help?
General